Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0014    Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0015    Camshaft Position "B" - Timing Over-Retarded (Bank 1)

DTC    P0024    Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0025    Camshaft Position "B" - Timing Over-Retarded (Bank 2)

for Preparation Click here


DESCRIPTION

HINT:
If DTC P0014, P0015, P0024 or P0025 is present, check the VVT (Variable Valve Timing) system.

The Variable Valve Timing (VVT) system includes the ECM, OCV and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.

A192077E02


DTC No.
DTC Detection Condition
Trouble Area
P0014
P0024
Exhaust valve timing is not adjusted in valve timing advance range
(2 trip detection logic)
  1. Valve timing
  2. Oil control valve (OCV) for exhaust camshaft
  3. OCV filter
  4. Camshaft timing exhaust gear
  5. ECM
P0015
P0025
Exhaust valve timing is not adjusted in valve timing retard range
(1 trip detection logic)
  1. Valve timing
  2. OCV for exhaust camshaft
  3. OCV filter
  4. Camshaft timing exhaust gear
  5. ECM

MONITOR DESCRIPTION

The ECM optimizes the exhaust valve timing using the VVT (Variable Valve Timing) system to control the exhaust camshaft. The VVT system includes the ECM, Oil Control Valve (OCV) and VVT controller.
The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the exhaust camshaft.
If the difference between the target and actual exhaust valve timing is large, and changes in actual exhaust valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores a DTC.

WIRING DIAGRAM

Refer to DTC P0013 .

INSPECTION PROCEDURE


HINT:

Abnormal Bank
Advanced Timing Over
(Valve Timing Out of Specified Range)
Retarded Timing Over
(Valve Timing Out of Specified Range)
Bank 1
P0014
P0015
Bank 2
P0024
P0025
  1. If DTC P0014 or P0015 is displayed, check the bank 1 VVT system for exhaust camshaft circuit.
  2. Bank 1 refers to the bank that includes No. 1 cylinder.
  3. If DTC P0024 or P0025 is displayed, check the bank 2 VVT system for exhaust camshaft circuit.
  4. Bank 2 refers to the bank that does not include No. 1 cylinder.
  5. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0014, P0015, P0024 or P0025
    A
    P0014, P0015, P0024 or P0025 and other DTCs
    B

    HINT:
    If any DTCs other than P0014, P0015, P0024 or P0025 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the intelligent tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the intelligent tester.

    OK:
    Tester Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Warm up the engine.

  1. Switch the ECM from normal mode to check mode using the intelligent tester (Click here).

  1. With the engine warmed up, idle it for 1 minute. Then drive the vehicle for 5 minutes.

  1. Read DTCs using the intelligent tester.

    OK:
    No DTC output.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

A166451E03

  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


5.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY (OCV FOR EXHAUST CAMSHAFT)
  1. Inspect the camshaft oil control valve assembly .



NG
REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER
  1. Remove the oil control valve filter (Click here).

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OIL CONTROL VALVE FILTER
OK


7.REPLACE CAMSHAFT TIMING EXHAUST GEAR
  1. Replace the camshaft timing exhaust gear (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Warm up the engine.

  1. Switch the ECM from normal mode to check mode using the intelligent tester (Click here).

  1. With the engine warmed up, idle it for 1 minute. Then drive the vehicle for 5 minutes.

  1. Read the output DTCs using the intelligent tester.

    OK:
    No DTC output.

    HINT:
    DTC P0014, P0015, P0024 or P0025 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

END