Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

  1. If the rear RH side manual UP/DOWN function does not operate, there may be a malfunction in the rear power window regulator switch RH, the rear power window regulator motor RH, the power window regulator master switch, the harness and connector.

WIRING DIAGRAM


B219836E02


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY)


    B149730E17
  1. Disconnect the N3 rear power window regulator switch RH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT REAR POWER WINDOW REGULATOR SWITCH RH


    B166141E05
  1. Remove the rear power window regulator switch RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (U) - 3 (B)
    UP
    Below 1 Ω
    1 (D) - 2 (SD)
    UP
    Below 1 Ω
    4 (U) - 5 (SU)
    OFF
    Below 1 Ω
    1 (D) - 2 (SD)
    OFF
    Below 1 Ω
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)
    DOWN
    Below 1 Ω



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW SWITCH RH - REAR POWER WINDOW MOTOR RH)


    B191455E03
  1. Disconnect the N3 rear power window regulator switch RH connector.

  1. Disconnect the N4 rear power window regulator motor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N3-1 (D) - N4-1
    Always
    Below 1 Ω
    N3-4 (U) - N4-2
    Always
    Below 1 Ω
    N3-1 (D) - Body ground
    Always
    10 kΩ or higher
    N3-4 (U) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
B161799E01
  1. Remove the rear power window regulator motor RH (Click here).

  1. Apply battery voltage and check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise



NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - REAR POWER WINDOW SWITCH RH)


    B191456E03
  1. Disconnect the M2 power window regulator master switch connector.

  1. Disconnect the N3 rear power window regulator switch RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M2-10 (U) - N3-5 (SU)
    Always
    Below 1 Ω
    M2-16 (D) - N3-2 (SD)
    Always
    Below 1 Ω
    M2-10 (U) - Body ground
    Always
    10 kΩ or higher
    M2-16 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)