Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2240    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)

DTC    P2241    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)

DTC    P2242    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

DTC    P2255    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)

DTC    P2256    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.

A178930E03


DTC No.
DTC Detection Condition
Trouble Area
P2237
P2240
Open in the circuit between terminals AF+ and AF- of the A/F sensor while engine is running
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor circuit
  2. Air Fuel Ratio (A/F) sensor
  3. ECM
P2238
P2241
  1. Case 1:
Condition (a) or (b) continues for 5.0 seconds or more
(2 trip detection logic):
(a) AF+ voltage 0.5 V or less
(b) (AF+) - (AF-) = 0.1 V or less
  1. Case 2:
A/F sensor admittance: Less than 0.022 1/Ω
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor circuit
  2. Air Fuel Ratio (A/F) sensor
  3. ECM
P2239
P2242
AF+ voltage more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor circuit
  2. Air Fuel Ratio (A/F) sensor
  3. ECM
P2252
P2255
AF- voltage 0.5 V or less for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor circuit
  2. Air Fuel Ratio (A/F) sensor
  3. ECM
P2253
P2256
AF- voltage more than 4.5 V for 5.0 seconds or more
(2 trip detection logic)
  1. Open or short in air fuel ratio sensor circuit
  2. Air Fuel Ratio (A/F) sensor
  3. ECM

HINT:
  1. DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 A/F sensor circuit.
  2. DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 A/F sensor circuit.
  3. Bank 1 refers to the bank that includes No. 1 cylinder.
  4. Bank 2 refers to the bank that includes No. 2 cylinder.


MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the A/F sensor circuit, or if A/F sensor output drops.
To detect these problems, the voltage of the A/F sensor is monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.6 V and 4.5 V, it is considered normal. If the voltage is outside of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in the next driving cycle, the MIL is illuminated and a DTC is stored.
The Air-Fuel Ratio (A/F) sensor varies its output voltage in proportion to the air-fuel ratio. If the A/F sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the A/F sensor circuit.

WIRING DIAGRAM


A164734E06


INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/ F sensor operation using the intelligent tester.
  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Start the engine and turn the intelligent tester on.
  3. (c) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. (d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
  5. (e) Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  6. (f) Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the intelligent tester.

HINT:
  1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
  1. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1
(A/F)
+25%
Rich
Less than 3.1 V
-12.5%
Lean
More than 3.4 V
O2S B1S2
(HO2)
+25%
Rich
More than 0.55 V
-12.5%
Lean
Less than 0.4 V
AFS Voltage B2S1
(A/F)
+25%
Rich
Less than 3.1 V
-12.5%
Lean
More than 3.4 V
O2S B2S2
(HO2)
+25%
Rich
More than 0.55 V
-12.5%
Lean
Less than 0.4 V

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E05
A150787E01
A150788E01
-
2
A150787E01
A150790E01
A150787E01
A150788E01
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E05
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/ F Sensor procedure enables technicians to check and graph the output voltages of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A160209E11
  1. Disconnect the A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D19-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D20-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.



  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D19-1 (HA1A) - D56-22 (HA1A)
    Always
    Below 1 Ω
    D19-3 (A1A+) - D56-126 (A1A+)
    Always
    Below 1 Ω
    D19-4 (A1A-) - D56-125 (A1A-)
    Always
    Below 1 Ω
    D20-1 (HA2A) - D56-20 (HA2A)
    Always
    Below 1 Ω
    D20-3 (A2A+) - D56-103 (A2A+)
    Always
    Below 1 Ω
    D20-4 (A2A-) - D56-102 (A2A-)
    Always
    Below 1 Ω
    D19-1 (HA1A) or D56-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    D19-3 (A1A+) or D56-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    D19-4 (A1A-) or D56-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    D20-1 (HA2A) or D56-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    D20-3 (A2A+) or D56-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    D20-4 (A2A-) or D56-102 (A2A-) - Body ground
    Always
    10 kΩ or higher


    A164715E05



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 5 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    No DTC is output
    A
    P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output
    B



B
REPLACE ECM (Click here)
A

END