DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1) |
DTC P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) |
DTC P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
DTC P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) |
DTC P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2237 P2240 | Open in the circuit between terminals AF+ and AF- of the A/F sensor while engine is running (2 trip detection logic) |
|
| P2238 P2241 |
(2 trip detection logic): (a) AF+ voltage 0.5 V or less (b) (AF+) - (AF-) = 0.1 V or less
(2 trip detection logic) |
|
| P2239 P2242 | AF+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| P2252 P2255 | AF- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic) |
|
| P2253 P2256 | AF- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (A/F) | -12.5%/ 0%/ +12.5% | Rich | Less than 3.1 V |
| -12.5%/ 0%/ +12.5% | Lean | More than 3.4 V | |
| O2S B1S2 (HO2) | -12.5%/ 0%/ +12.5% | Rich | More than 0.55 V |
| -12.5%/ 0%/ +12.5% | Lean | Less than 0.4 V | |
| AFS Voltage B2S1 (A/F) | -12.5%/ 0%/ +12.5% | Rich | Less than 3.1 V |
| -12.5%/ 0%/ +12.5% | Lean | More than 3.4 V | |
| O2S B2S2 (HO2) | -12.5%/ 0%/ +12.5% | Rich | More than 0.55 V |
| -12.5%/ 0%/ +12.5% | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
Disconnect the A/F sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D19-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| D20-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D19-1 (HA1A) - D56-22 (HA1A) | Always | Below 1 Ω |
| D19-3 (A1A+) - D56-126 (A1A+) | Always | Below 1 Ω |
| D19-4 (A1A-) - D56-125 (A1A-) | Always | Below 1 Ω |
| D20-1 (HA2A) - D56-20 (HA2A) | Always | Below 1 Ω |
| D20-3 (A2A+) - D56-103 (A2A+) | Always | Below 1 Ω |
| D20-4 (A2A-) - D56-102 (A2A-) | Always | Below 1 Ω |
| D19-1 (HA1A) or D56-22 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D19-3 (A1A+) or D56-126 (A1A+) - Body ground | Always | 10 kΩ or higher |
| D19-4 (A1A-) or D56-125 (A1A-) - Body ground | Always | 10 kΩ or higher |
| D20-1 (HA2A) or D56-20 (HA2A) - Body ground | Always | 10 kΩ or higher |
| D20-3 (A2A+) or D56-103 (A2A+) - Body ground | Always | 10 kΩ or higher |
| D20-4 (A2A-) or D56-102 (A2A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 3.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read pending DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output | B |
|
| ||||
| A | ||
| ||