DTC B1810/53 Short in Driver Side Squib 2nd Step Circuit |
DTC B1811/53 Open in Driver Side Squib 2nd Step Circuit |
DTC B1812/53 Short to GND in Driver Side Squib 2nd Step Circuit |
DTC B1813/53 Short to B+ in Driver Side Squib 2nd Step Circuit |
| DTC Code | Detection Condition | Trouble Area |
| B1810/53 | When one of following conditions is met:
|
|
| B1811/53 | When one of following conditions is met:
|
|
| B1812/53 | When one of following conditions is met:
|
|
| B1813/53 | When one of following conditions is met:
|
|

| 1.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connector is properly connected to the steering pad.
Disconnect the connector from the steering pad.
Check that the spiral cable connector (on the steering pad side) is not damaged.
|
| ||||
| OK | |
| 2.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP) |
![]() |
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
Check that the connector is properly connected to the center airbag sensor assembly.
Disconnect the connector from the center airbag sensor assembly.
Check that the terminal of the connector is not damaged.
Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.
|
| ||||
| OK | |
| 4.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z8-2 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| z8-1 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z8-2 (D2+) - z8-1 (D2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z8-2 (D2+) - z8-1 (D2-) | Always | 1 MΩ or higher |
| z8-2 (D2+) - Body ground | Always | 1 MΩ or higher |
| z8-1 (D2-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the steering pad and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK CONNECTOR |
Restore the released activation prevention mechanism of connector B to the original condition.
Check that the connectors that link the spiral cable and instrument panel wire harness are properly connected.
Disconnect the connectors that link the spiral cable and instrument panel wire.
Check that the terminals of the connectors are not damaged.
Check that the short spring for the spiral cable connector with the activation prevention mechanism is not deformed or damaged.
|
| ||||
| OK | |
| 7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H13-4 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| H13-3 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H13-4 (D2+) - H13-3 (D2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H13-4 (D2+) - H13-3 (D2-) | Always | 1 MΩ or higher |
| H13-4 (D2+) - Body ground | Always | 1 MΩ or higher |
| H13-3 (D2-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||