DTC B1653/35 Seat Position Airbag Sensor Circuit Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1653/35 | When one of following conditions is met:
|
|

| 1.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the seat position airbag sensor.
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and the seat position airbag sensor.
Check that the connectors (on the center airbag sensor side and seat position airbag sensor side) are not damaged (Click here).
|
| ||||
| OK | |
| 3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (CENTER AIRBAG SENSOR - SEAT POSITION AIRBAG SENSOR) |

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Ignition switch ON | Below 1 V |
| 2 - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 1 MΩ or higher |
| 1 - Body ground | Always | 1 MΩ or higher |
| 2 - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK SEAT POSITION AIRBAG SENSOR |
![]() |
Connect the connectors to the center airbag sensor and the seat position airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 5.REPLACE SEAT POSITION AIRBAG SENSOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the seat position airbag sensor (Click here).
| NEXT | |
| 6.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 7.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH) |

Disconnect the floor wire connector from the front seat inner belt LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O4-2 (LSP+) - Body ground | Ignition switch ON | Below 1 V |
| O4-4 (LSP-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O4-2 (LSP+) - O4-4 (LSP-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O4-2 (LSP+) - O4-4 (LSP-) | Always | 1 MΩ or higher |
| O4-2 (LSP+) - Body ground | Always | 1 MΩ or higher |
| O4-4 (LSP-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||