DTC B1860/64 Short in Driver Side Knee Airbag Squib Circuit |
DTC B1861/64 Open in Driver Side Knee Airbag Squib Circuit |
DTC B1862/64 Short to GND in Driver Side Knee Airbag Squib Circuit |
DTC B1863/64 Short to B+ in Driver Side Knee Airbag Squib Circuit |
| DTC Code | Detection Condition | Trouble Area |
| B1860/64 | When one of the following conditions is met:
|
|
| B1861/64 | When one of the following conditions is met:
|
|
| B1862/64 | When one of the following conditions is met:
|
|
| B1863/64 | When one of the following conditions is met:
|
|

| 1.CHECK DRIVER SIDE KNEE AIRBAG (DRIVER SIDE KNEE SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the driver side knee airbag.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the instrument panel wire connector (on the driver side knee airbag side) is not damaged.
|
| ||||
| OK | |
| 3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG CIRCUIT) |
![]() |
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H109-1 (DK+) - Body ground | Ignition switch ON | Below 1 V |
| H109-2 (DK-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H109-1 (DK+) - H109-2 (DK-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H109-1 (DK+) - H109-2 (DK-) | Always | 1 MΩ or higher |
| H109-1 (DK+) - Body ground | Always | 1 MΩ or higher |
| H109-2 (DK-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the driver side knee airbag and center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| OK | A |
| NG (w/ Cool Box) | B |
| NG (w/o Cool Box) | C |
|
| ||||
|
| ||||
| A | ||
| ||