Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1865/65    Short in Front Passenger Side Knee Airbag Squib Circuit

DTC    B1866/65    Open in Front Passenger Side Knee Airbag Squib Circuit

DTC    B1867/65    Short to GND in Front Passenger Side Knee Airbag Squib Circuit

DTC    B1868/65    Short to B+ in Front Passenger Side Knee Airbag Squib Circuit

for Preparation Click here


DESCRIPTION

The front passenger side knee airbag squib circuit consists of the center airbag sensor and front passenger side knee airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side knee airbag squib circuit.

DTC Code
Detection Condition
Trouble Area
B1865/65
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the front passenger side knee airbag squib circuit during the primary check.
  2. A front passenger side knee airbag squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Front passenger side knee airbag assembly (Front passenger side knee squib)
  3. Center airbag sensor assembly
B1866/65
When one of the following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the front passenger side knee airbag squib circuit for 2 seconds.
  2. A front passenger side knee airbag squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Front passenger side knee airbag assembly (Front passenger side knee squib)
  3. Center airbag sensor assembly
B1867/65
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the front passenger side knee airbag squib circuit for 0.5 seconds.
  2. A front passenger side knee airbag squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Front passenger side knee airbag assembly (Front passenger side knee squib)
  3. Center airbag sensor assembly
B1868/65
When one of the following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the front passenger side knee airbag squib circuit for 0.5 seconds.
  2. A front passenger side knee airbag squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Front passenger side knee airbag assembly (Front passenger side knee squib)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C146265E18


INSPECTION PROCEDURE

HINT:
To perform the simulation method, enter "check mode" (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).

1.CHECK FRONT PASSENGER SIDE KNEE AIRBAG (FRONT PASSENGER SIDE KNEE SQUIB)
C168657E08
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front passenger side knee airbag.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front passenger side knee airbag (front passenger side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1865, B1866, B1867 or B1868 is not output.

    HINT:
    Codes other than DTC B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

REPLACE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (Click here)  

2.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the instrument panel wire connector (on the front passenger side knee airbag side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


3.CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE KNEE SQUIB CIRCUIT)
C168658E08
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H108-1 (PK+) - Body ground
    Ignition switch ON
    Below 1 V
    H108-2 (PK-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H108-1 (PK+) - H108-2 (PK-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H108-1 (PK+) - H108-2 (PK-)
    Always
    1 MΩ or higher
    H108-1 (PK+) - Body ground
    Always
    1 MΩ or higher
    H108-2 (PK-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK


4.CHECK CENTER AIRBAG SENSOR
C146268E05
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front passenger side knee airbag and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1865, B1866, B1867 or B1868 is not output.

    HINT:
    Codes other than DTC B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)