Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

DTC    B2603    Tilt and Telescopic Manual Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

Different voltage values are input to the multiplex tilt and telescopic ECU by operating the tilt and telescopic manual switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should be moved based on the voltage value.

DTC Code
Detection Condition
Trouble Area
B2603
When operating the tilt and telescopic manual switch, an abnormal voltage value is input to the multiplex tilt and telescopic ECU.
  1. Tilt and telescopic manual switch
  2. Tilt and telescopic manual switch circuit
  3. Multiplex tilt and telescopic ECU

WIRING DIAGRAM


C159015E03


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (TILT AND TELESCOPIC MANUAL SWITCH)
C113518E01
  1. Use the Data List to check if the tilt and telescopic manual switch is functioning properly.

    Tilt & Telescopic 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    T&T Manual SW data
    Voltage data of manual switch/min.: 0.00 V, max.: 4.99 V
    Neutral position: Below 0.2 V
    Tilt up: 1.67 to 2.13 V
    Tilt down: 0.54 to 0.74 V
    Telescopic contract: 1.08 to 1.40 V
    Telescopic extend: 2.22 to 2.77 V
    -

Result 
Result
Proceed to
Switch voltages in all directions are outside the standard.
A
Switch voltages in certain directions are outside the standard.
B
Switch voltages in all directions are within the standard.
C


B
REPLACE HEADLIGHT DIMMER SWITCH (Click here)

C
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
A


2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - HEADLIGHT DIMMER SWITCH)

C159212E03

  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Disconnect the H11 headlight dimmer switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H57-4 (VC) - H11-8 (VC)
    Always
    Below 1 Ω
    H57-3 (MSW) - H11-10 (MSW)
    Always
    Below 1 Ω
    H11-8 (VC) - Body ground
    Always
    10 kΩ or higher
    H11-10 (MSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)


    C149088E29
  1. Reconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H57-4 (VC) - H57-3 (MSW)
    Ignition switch ON
    4.9 to 5.1 V



NG
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
OK


4.INSPECT HEADLIGHT DIMMER SWITCH (TILT AND TELESCOPIC MANUAL SWITCH)


    C160341E04
  1. Disconnect the H11 headlight dimmer switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (VC) - 10 (MSW)
    Tilt up
    360 Ω
    Tilt down
    1990 Ω
    Telescopic contract
    790 Ω
    Telescopic extend
    160 Ω



NG
REPLACE HEADLIGHT DIMMER SWITCH (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)