Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0500    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A115899E04


DTC No.
DTC Detection Condition
Trouble Area
P0500
While vehicle being driven, no vehicle speed sensor signal transmitted to ECM
(2 trip detection logic)
  1. Open or short in speed signal circuit
  2. Wheel speed sensor
  3. Combination meter
  4. ECM
  5. Skid control ECU

MONITOR DESCRIPTION


  1. The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM


A185017E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).



NG
GO TO MALFUNCTION IN SPEEDOMETER (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the intelligent tester.

    OK:
    Vehicle speeds displayed on the intelligent tester and speedometer display are equal.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.INSPECT COMBINATION METER ASSEMBLY (+S VOLTAGE)
A127854E18
  1. Disconnect the combination meter connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-35 (+S) - Body ground
    Ignition switch ON
    4.5 to 5.5 V



NG
Go to step 5
OK


4.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
A127943E25
  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-35 (+S) - Body ground
    1. Ignition switch ON
    2. Wheel is turned slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    H37-35 (+S) - A27-13 (SPD)
    Always
    Below 1 Ω
    H37-35 (+S) or A27-13 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)