Home › Engine / Hybrid System › 3UR-FE COOLING › RADIATOR

RADIATOR > INSTALLATION

for Preparation Click here



1. INSTALL OUTLET RADIATOR HOSE


    A198569E01
  1. Install the outlet radiator hose into the radiator.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



2. INSTALL RADIATOR ASSEMBLY


    A151752
  1. Set the radiator bracket hooks to the radiator support holes.

  1. Install the radiator with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



3. INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (for LH Side)


    A183237
  1. Install the No. 1 radiator to support seal with the 3 clips.



4. INSTALL NO. 1 RADIATOR TO SUPPORT SEAL (for RH Side)


    A183236
  1. Install the No. 1 radiator to support seal with the 3 clips.



5. INSTALL RADIATOR SIDE DEFLECTOR LH


    A151774
  1. Install the deflector with the 6 clips.

  1. Connect the wire harness clamp.



6. INSTALL FAN SHROUD


    A151842
  1. Install the fan pulley to the fan bracket.

  1. Place the shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.



    A183238
  1. Attach the shroud claws to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the reservoir hose to the upper radiator tank.



    A187694
  1. Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.

    HINT:
    Align the hose clamp with the white paint mark on the hose, and install the hose clamp so that the hose clamp lock is between the fan shroud stoppers.

  1. Install the fan and generator V belt .

  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



7. INSTALL INLET RADIATOR HOSE


    A198570E01
  1. Install the inlet radiator hose.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



8. CONNECT OUTLET RADIATOR HOSE


    A183234E01
  1. Connect the outlet radiator hose to the water inlet housing.



9. INSTALL OIL COOLER ASSEMBLY


    A162475
  1. Apply a light coat of engine oil to 2 new O-rings.

  1. Install the 2 O-rings to the oil cooler.



    A162471
  1. Install the oil cooler with the 5 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



10. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    14.6 liters (15.4 US qts., 12.8 Imp. qts.)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



11. INSPECT FOR COOLANT LEAK


A161766E01

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



12. INSTALL NO. 1 FRONT BUMPER SIDE RETAINER SUB-ASSEMBLY RH
  1. Install the No. 1 front bumper side retainer RH with the 6 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



13. CONNECT NO. 1 HEADLAMP CLEANER HOSE


14. INSTALL FRONT BUMPER COVER ASSEMBLY
  1. Install the front bumper cover assembly (Click here).



15. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. Bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. Screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



16. INSTALL V-BANK COVER SUB-ASSEMBLY


A165576E03
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.