DTC B1781 Front Occupant Classification Sensor RH Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1781 | One of following conditions is met:
|
|

| 1.CHECK FOR DTCs |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the front occupant detection sensor RH.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Check that the connectors (on the occupant classification ECU side and front occupant detection sensor RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH (FRONT OCCUPANT DETECTION SENSOR RH CIRCUIT) |

Disconnect the connectors from the occupant classification ECU and the front occupant detection sensor RH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| W1-2 (SGD2) - Body ground | Ignition switch ON | Below 1 V |
| W1-8 (SIG2) - Body ground | ||
| W1-12 (SVC2) - Body ground |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using service wires, connect terminals 1 (SVC2) and 3 (SGD2), and connect terminals 2 (SIG2) and 3 (SGD2) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1-8 (SIG2) - W1-2 (SGD2) | Always | Below 1 Ω |
| W1-12 (SVC2) - W1-2 (SGD2) |
Disconnect the service wires from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W1-8 (SIG2) - W1-2 (SGD2) | Always | 1 MΩ or higher |
| W1-12 (SVC2) - W1-2 (SGD2) | ||
| W1-8 (SIG2) - W1-12 (SVC2) | ||
| W1-2 (SGD2) - Body ground | ||
| W1-8 (SIG2) - Body ground | ||
| W1-12 (SVC2) - Body ground |
|
| ||||
| OK | |
| 5.CHECK FOR DTCs |
Connect the connectors to the occupant classification ECU and the front occupant detection sensor RH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 6.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant classification ECU.
| NEXT | |
| 7.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the intelligent tester, perform the zero point calibration (Click here).
|
| ||||
| OK | |
| 8.PERFORM SENSITIVITY CHECK |
Using the intelligent tester, perform the sensitivity check (Click here).
|
| ||||
| OK | |
| 9.CHECK FOR DTCs |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 10.REPLACE FRONT SEAT ASSEMBLY RH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the front seat assembly RH.
| NEXT | |
| 11.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the intelligent tester, perform the zero point calibration (Click here).
| NEXT | |
| 12.PERFORM SENSITIVITY CHECK |
Using the intelligent tester, perform the sensitivity check (Click here).
| NEXT | ||
| ||