Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL

REAR DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, remove the filler plug and gasket.

    2. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.

    3. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. for Rear Differential:

    1. Using a 10 mm hexagon wrench, remove the filler plug and gasket.

    2. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.

    3. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.

      Torque:
      65 N*m{ 660 kgf*cm , 48 ft.*lbf }



2. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft assembly (Click here).



3. REMOVE REAR DRIVE PINION NUT


    C181003E01
  1. Using SST and a hammer, unstake the rear drive nut.

    SST
    09930-00010  



    C181026E01
  1. Using SST to hold the rear drive pinion companion flange sub-assembly.

    SST
    09330-00021  

  1. Using a socket wrench (30mm), remove the rear drive pinion nut.

    NOTICE:
    Install nuts on the bolts to protect them, as shown in the illustration.



4. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C181017E01
  1. Using SST, remove the rear drive pinion companion flange sub-assembly from the rear differential carrier assembly.

    HINT:
    Use the propeller shaft installation nuts when mounting SST on the flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010)
    09955-03050  



5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    F040717E03
  1. Using SST, remove the oil seal.

    SST
    09308-10010  



6. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


7. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C180990E01
  1. Remove the bearing (inner race) from the differential carrier.

    SST
    09950-40011   (09951-04010, 09953-04020, 09952-04010, 09954-04010)
    09955-04110  
    09958-04020  



8. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


9. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new bearing spacer.



10. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C181021E01
  1. Using SST and a hammer, lightly tap in the bearing (inner race) to install it.

    SST
    09316-60011   (09316-00011)
    09506-30012  



11. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


12. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


    C181145E01
  1. Using SST and a plastic-faced hammer, tap in a new oil seal until its surface is flush with the differential carrier end.

    SST
    09223-56010  
    09527-17011  

    Standard oil seal depth:
    0 to 1.0 mm (0 to 0.0394 in.)

    HINT:
    Connect 2 SST with vinyl tape.

  1. Coat the lip of the oil seal with MP grease.



13. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
  1. Place the companion flange on the drive pinion.

  1. Coat the threads of a new nut with hypoid gear oil.



    C181027E01
  1. Using SST to hold the companion flange.

    NOTICE:
    Install nuts on the bolts to protect them, as shown in the illustration.

    SST
    09330-00021  

  1. Using a socket wrench (30mm), tighten the nut.

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less



14. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C181029
  1. Using a torque wrench, measure the preload.

    Standard Preload (at Starting):
    Item
    Specified Condition
    New bearing
    2.04 to 3.24 N*m (21 to 33 kgf*cm, 18 to 29 in.*lbf)
    Reused bearing
    1.52 to 2.23 N*m (15 to 23 kgf*cm, 13 to 20 in.*lbf)

    If the result is not as specified, adjust the preload.



15. STAKE REAR DRIVE PINION NUT


    C181003E01
  1. Using a chisel and hammer, stake the nut.

    SST
    09930-00010  



16. INSTALL PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft assembly (Click here).



17. ADD DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil Type:
    Item
    Oil Type and Viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front Differential Capacity:
    Specified Condition
    2.00 to 2.10 liters (2.1 to 2.2US qts., 1.7 to 1.8 Imp. qts.)

    Rear Differential Capacity:
    Specified Condition
    1.50 to 1.60 liters (1.6 to 1.7 US qts., 1.3 to 1.4 Imp. qts.)

  1. for Rear Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }