Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1650/32    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor and the occupant classification system.
If the center airbag sensor receives signals from the occupant classification ECU, it determines whether the front passenger airbag, the front seat side airbag RH and front seat outer belt should be operated.
DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC Code
Detection Condition
Trouble Area
B1650/32
When one of following conditions is met:
  1. Occupant classification system malfunction
  2. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit for 2 seconds.
  3. Center airbag sensor malfunction
  1. Front seat wire RH (w/ power seat)
  2. Occupant classification system
  3. Center airbag sensor assembly
  4. No. 2 floor wire

WIRING DIAGRAM


C158891E03


INSPECTION PROCEDURE

1.CHECK FOR DTC (OCCUPANT CLASSIFICATION ECU)
  1. Turn the ignition switch to ON, and wait for at least 10 seconds.

  1. Check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC is not output.



NG
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
OK


2.CHECK VEHICLE SYSTEM
  1. Check vehicle system.
    Result 
    Result
    Proceed to
    w/ Power seat
    A
    w/o Power seat
    B



B
Go to step 8
A


3.CHECK FOR DTC (CENTER AIRBAG SENSOR)
C146235E01
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1650/32 is not output.

    HINT:
    Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.



NG
Go to step 4
OK

USE SIMULATION METHOD TO CHECK (Click here)  

4.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the occupant classification ECU.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


5.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the occupant classification ECU.

  1. Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT

C159566E02

  1. Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W6-8 (FSR+) - W6-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W6-8 (FSR+) - W6-4 (FSR-)
    Always
    1 MΩ or higher
    W6-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    W6-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W6-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    W6-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 7
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

7.CHECK NO. 2 FLOOR WIRE

C183103E01

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the front seat wire RH connector from the No. 2 floor wire.

  1. Using a service wire, connect terminal 12 (FSP+) and 13 (FSP-) of connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PW1-8 (FSR+) - PW1-9 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PW1-8 (FSR+) - PW1-9 (FSR-)
    Always
    1 MΩ or higher
    PW1-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    PW1-9 (FSR-) - Body ground
    Always
    1 MΩ or higher

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    PW1-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    PW1-9 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

8.CHECK FOR DTC (CENTER AIRBAG SENSOR)
C146230E17
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1650/32 is not output.

    HINT:
    Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.



NG
Go to step 9
OK

USE SIMULATION METHOD TO CHECK (Click here)  

9.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the occupant classification ECU.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


10.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the occupant classification ECU.

  1. Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (Click here).

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


11.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - OCCUPANT CLASSIFICATION ECU)

C172831E02

  1. Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P14-8 (FSR+) - P14-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P14-8 (FSR+) - P14-4 (FSR-)
    Always
    1 MΩ or higher
    P14-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    P14-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P14-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    P14-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)