Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

DTC    B15D5    Rear Seat Entertainment System Disconnected

for Preparation Click here


DESCRIPTION

The radio and display receiver assembly and television display assembly are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the radio and display receiver assembly and television display assembly, this DTC will be stored.

DTC Code
DTC Detection Condition
Trouble Area
B15D5
When either condition below is met:
  1. The television display assembly is/was not connected while the ignition switch is ON or ACC.
  2. Communication between the master unit and the television display assembly is not possible when the engine is started.
  1. AVC-LAN communication line
  2. Television display assembly
  3. Radio and display receiver assembly
  4. Harness or connector

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The radio and display receiver assembly is the master unit.


WIRING DIAGRAM


E302038E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTOR CONNECTION CONDITION
  1. Check that the television display assembly and radio and display receiver assembly connectors are connected properly.

    OK:
    The connectors are connected properly.



NG
CONNECT CONNECTOR CORRECTLY
OK


3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)


    E192430E66
  1. Disconnect the television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U13-17 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    U13-1 (+B) - Body ground
    Always
    11 to 14 V
    U13-2 (ACC) - Body ground
    Ignition switch ACC
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Television Display Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
  1. Disconnect the I57 radio and display receiver assembly connector.

  1. Disconnect the U13 television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I57-9 (TXM+) - U13-3 (TX1+)
    Always
    Below 1 Ω
    I57-10 (TXM-) - U13-4 (TX1-)
    Always
    Below 1 Ω
    I57-9 (TXM+) - Body ground
    Always
    10 kΩ or higher
    I57-10 (TXM-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK TELEVISION DISPLAY ASSEMBLY
  1. Replace the television display assembly with a known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)