Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

DTC    B15D5    Rear Seat Entertainment System Disconnected

for Preparation Click here


DESCRIPTION

The navigation receiver assembly and television display assembly are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigation receiver assembly and television display assembly, these DTCs will be stored.

DTC Code
DTC Detection Condition
Trouble Area
B15D5
A device that is listed in the AVC-LAN network connected device record of the master unit is missing.
  1. Television display assembly power source circuit
  2. AVC-LAN circuit between television display assembly and navigation receiver assembly
  3. Television display assembly
  4. Navigation receiver assembly

HINT:
For the AVC-LAN network, the navigation receiver assembly is the master unit.


WIRING DIAGRAM


E283431E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.
      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
      2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE) 

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - POWER SOURCE AND BODY GROUND)


    E283174E01
  1. Disconnect the television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U13-17 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    U13-1 (+B) - U13-17 (GND)
    Always
    11 to 14 V
    U13-2 (ACC) - U13-17 (GND)
    Ignition switch ACC
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Television Display Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
  1. Disconnect the U13 television display assembly connector.

  1. Disconnect the I46 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U13-3 (TX1+) - I46-9 (TXM+)
    Always
    Below 1 Ω
    U13-4 (TX1-) - I46-10 (TXM-)
    Always
    Below 1 Ω
    U13-3 (TX1+) - Body ground
    Always
    10 kΩ or higher
    U13-4 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE TELEVISION DISPLAY ASSEMBLY
  1. Replace the television display assembly (Click here).


NEXT


7.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)