Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    01-D6    No Master

DTC    01-D7    Connection Check Error

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
01-D6*1
When either of the following conditions is met:
  1. The device that stores (stored) the code has (had) been disconnected when the ignition switch is ACC or ON.
  1. The master device has (had) been disconnected when this code is stored.
  1. Radio receiver power source circuit
  1. Power source circuit of the component which has stored this code
  1. AVC-LAN circuit between the radio receiver assembly and the component which has stored this code
  1. Component which has stored this code
  1. Radio receiver assembly
01-D7*2
When either of the following conditions is met:
  1. The device that stored the code has (had) been disconnected after the engine starts (started).
  1. The master device has (had) been disconnected when this code is (was) stored.

HINT:
  1. *1: Even if no fault is present, this trouble code may be stored depending on the battery condition or engine start voltage.
  2. *2: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.

NOTICE:
  1. Before starting troubleshooting, be sure to clear DTCs to clear codes stored due to the reasons described in Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The radio receiver assembly is the master unit.
  3. Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read Description before performing the following procedures.

1.CHECK RADIO RECEIVER POWER SOURCE CIRCUIT
  1. Refer to Radio Receiver Power Source Circuit (Click here).

    HINT:
    If the power source circuit is operating normally, proceed to the next step.


NEXT


2.IDENTIFY THE COMPONENT WHICH HAS STORED THIS CODE


  1. Enter the diagnostic mode.


    E146440E02

  1. Press the preset switch "3" to change to "Detailed Information Mode".

  1. Identify the component which has stored this code.
    Component Table 
    Component
    Physical Address
    Stereo component amplifier
    440
    Television display*
    1B0

*: w/ Rear Seat Entertainment System

HINT:
  1. "440 (stereo component amplifier)" is the component which has stored this code in the example shown in the illustration.
  2. For details of the DTC display, refer to "DTC Check/Clear" (Click here).


NEXT


3.CHECK POWER SOURCE CIRCUIT OF COMPONENT WHICH HAS STORED THIS CODE
  1. Inspect the power source circuit of the component which has stored this code.

    HINT:
    If the power source circuit is operating normally, proceed to the next step.

    Component Table 
    Component
    Proceed to
    Stereo component amplifier
    Stereo Component Amplifier Power Source Circuit (Click here)
    Television display*
    Television Display Assembly Power Source Circuit (Click here)
    *: w/ Rear Seat Entertainment System


NEXT


4.INSPECT RADIO RECEIVER ASSEMBLY


    E145834E14
  1. Remove the radio receiver assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    5 (ATX+) - 15 (ATX-)
    Always
    60 to 80 Ω
    9 (TXM+) - 10 (TXM-)*
    Always
    60 to 80 Ω

    *: w/ Rear Seat Entertainment System



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)

E142358E04

HINT:
For details of the connectors, refer to "Terminals of ECU" (Click here).

  1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the radio receiver assembly and the component which has stored this code.

    1. Disconnect all connectors between the radio receiver assembly and the component which has stored this code.

    2. Check for an open or short in the AVC-LAN circuit between the radio receiver assembly and the component which has stored this code.

      OK:
      There is no open or short circuit.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE COMPONENT WHICH HAS STORED THIS CODE
  1. Replace the component which has stored this code with a normal one and check if the same problem occurs again.

    OK:
    Same problem does not occur.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

END