BACK DOOR > REASSEMBLY |
| 1. INSTALL REAR SPOILER COVER |
![]() |
Attach the 5 pins to install the rear spoiler cover.
![]() |
Install the 2 nuts.
![]() |
Install the 2 hole plugs.
Connect the connector.
| 2. INSTALL REAR LIGHT ASSEMBLY RH |
![]() |
Attach the clip and install the rear light.
Install the 2 nuts.
Connect the connector.
| 3. INSTALL REAR LIGHT ASSEMBLY LH |
![]() |
Attach the clip and install the rear light.
Install the 2 nuts.
Connect the connector.
| 4. INSTALL BACK DOOR LOCK (w/o Power Back Door) |
![]() |
Install the back door lock with the 3 bolts.
Connect the connector.
Attach the clamp.
| 5. INSTALL BACK DOOR LOCK (w/ Power Back Door) |
![]() |
Install the back door lock with the 4 bolts.
Connect the connector.
Attach the clamp.
| 6. INSTALL BACK DOOR LOCK PROTECTOR |
![]() |
Attach the 3 claws to install the back door lock protector sub-assembly.
| 7. INSTALL BACK DOOR OUTSIDE HANDLE |
![]() |
Install the back door outside handle with the 2 bolts.
Attach the clamp.
Connect the connector.
| 8. INSTALL LICENSE PLATE LIGHT ASSEMBLY |
Install the licence plate light with the 4 screws.
![]() |
Connect the 4 harness clamps.
Connect the 4 harness clamps and install the license plate light.
| 9. INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/Television Camera:) |
![]() |
Attach the 2 claws and install the rear television camera.
![]() |
Connect the connector.
| 10. INSTALL BACK DOOR OUTSIDE GARNISH |
![]() |
Attach the 2 clips to install the back door outside garnish.
![]() |
Install the 4 nuts.
Connect the connector.
| 11. INSTALL BACK DOOR LOCK CYLINDER |
![]() |
Install the back door lock cylinder with the 2 nuts.
Connect the connector.
| 12. INSTALL BACK DOOR POWER WINDOW REGULATOR ASSEMBLY |
![]() |
Apply MP grease to the sliding and rotating areas of the back door power window regulator.
Insert the back door power window regulator into the door panel. Provisionally tighten nut A to hang the back door power window regulator on the door panel.
Install the back door power window regulator with the 5 nuts, and tighten nut A.
Connect the connector.
| 13. INSTALL BACK DOOR GLASS |
![]() |
Install the back door glass onto the back door power window regulator with the 4 bolts.
Connect the 2 connectors.
![]() |
Install the hole plug.
| 14. INSTALL BACK DOOR GLASS RUN |
![]() |
Install a new back door glass run.
| 15. INSTALL BACK DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
![]() |
Attach the 9 claws to install the back door glass outer weatherstrip.
| 16. INSTALL BACK DOOR OUTSIDE MOULDING LH |
![]() |
Attach the 5 clips to install a new back door outside moulding.
| 17. INSTALL BACK DOOR OUTSIDE MOULDING RH |
| 18. INSTALL REAR WIPER STOPPER |
![]() |
Attach the claw and guide to install the liner wiper step.
| 19. INSTALL REAR WIPER MOTOR GROMMET |
![]() |
Apply MP grease to the entire surface of the wiper motor grommet lip.
![]() |
Install the rear wiper motor grommet with the mark directed up.
| 20. INSTALL REAR WIPER MOTOR ASSEMBLY |
![]() |
Install the rear wiper motor with the 3 bolts.
Connect the connector and clamp.
| 21. INSTALL REAR WIPER BLADE ASSEMBLY |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
Clean the wiper pivot serrations with a wire brush.
Operate the wiper, and then stop the windshield wiper motor in the automatic stop position.
![]() |
With the rear wiper blade and linear wiper step in the positions shown in the illustration, install the rear wiper blade assembly with the nut.
![]() |
Place the rear wiper blade assembly in the automatic stop position.
| 22. INSTALL REAR WIPER ARM HEAD CAP |
![]() |
Attach the claw to install the rear wiper head cap.
| 23. INSTALL POWER BACK DOOR SENSOR RH |
| 24. INSTALL POWER BACK DOOR SENSOR LH |
| 25. INSTALL BACK DOOR NO. 2 SERVICE HOLE COVER |
![]() |
Attach the 2 clips to install the back door No. 2 service hole cover with the 3 screws.
| 26. INSTALL MULTIPLEX NETWORK BODY ECU (w/ Power Back Door) |
![]() |
Install the multiplex network body ECU with the 2 screws.
Connect the 2 connector and attach the 2 clamps.
| 27. INSTALL POWER BACK DOOR WARNING BUZZER (w/ Power Back Door) |
![]() |
Attach the clamp to install the power back door warning buzzer.
Connect the connector.
| 28. INSTALL BACK DOOR SERVICE HOLE COVER |
![]() |
Apply butyl tape to the door panel, then install a new back door service hole cover as shown in the illustration.
| 29. INSTALL BACK DOOR GLASS WEATHERSTRIP |
![]() |
Install a new back door glass weatherstrip on the back door trim board assembly and fold down the 9 claws, as shown in the illustration.
| 30. INSTALL BACK DOOR TRIM BOARD ASSEMBLY |
![]() |
Attach the 11 clips to install the back door trim board assembly.
| 31. INSTALL BACK DOOR PULL STRAP |
![]() |
Install the back door pull strap with the bolt.
| 32. INSTALL BACK DOOR STRAP COVER |
![]() |
Attach the claw to slid the back door strap cover as shown in the illustration, and install it.
| 33. INSTALL BACK DOOR STAY LOWER BRACKET (w/ Power Back Door) |
![]() |
Install the back door stay lower bracket with the 2 bolts.
| 34. INSTALL BACK DOOR SIDE GARNISH LH |
![]() |
Attach the 3 clips to install the back door side garnish LH.
| 35. INSTALL BACK DOOR SIDE GARNISH RH |
![]() |
Attach the 2 clips to install the back door side garnish RH.
| 36. INSTALL BACK DOOR CENTER GARNISH |
![]() |
Attach the 4 clips and the claw to install the back door center garnish.
| 37. INSTALL POWER BACK DOOR ROD (w/ Power Back Door) |
![]() |
Install the power back door rod with the 2 stop rings.
| 38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 39. CHECK SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).