VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON |

| 1.PREPARE FOR INSPECTION |
Check that both of the following conditions are satisfied.
| NEXT | |
| 2.CHECK DTC |
Check if any ABS DTCs are output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 3.CHECK CAN COMMUNICATION SYSTEM |
Check if the CAN communication system DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 4.CHECK CONNECTOR CONNECTION CONDITION |
Check if the skid control ECU connector is connected securely.
|
| ||||
| OK | |
| 5.CHECK PARKING BRAKE SWITCH ASSEMBLY |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester ON.
Select Data List mode and check the parking brake switch using the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied OFF: Parking brake released | - |
Check that "ON" and "OFF" are properly indicated on the intelligent tester display when the parking brake lever is operated.
|
| ||||
| OK | |
| 6.CHECK BRAKE FLUID LEVEL WARNING SWITCH |

Remove the reservoir tank cap and strainer.
Disconnect the A3 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (+) - 2 (E) | Float up (Switch OFF) | 10 kΩ or higher |
| 1 (+) - 2 (E) | Float down (Switch ON) | Below 1 Ω |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH) |
![]() |
Disconnect the H37 meter connector.
Disconnect the A3 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H37-14 (SW) - A3-1 (+) | Always | Below 1 Ω |
| H37-14 (SW) - Body ground | Always | 10 kΩ or higher |
| A3-2 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BRAKE WARNING LIGHT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester ON.
Select Active Test mode and operate the brake warning light using the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Brake Warning Light | Brake warning light | Warning light ON/OFF | Observe combination meter |
Check that the brake warning light turns on and off in the combination meter using the intelligent tester.
|
| ||||
| OK | ||
| ||
| 9.INSPECT PARKING BRAKE SWITCH ASSEMBLY |
![]() |
Disconnect the A5 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Parking brake switch ON (Switch pin released) | Below 1 Ω |
| 1 - Body ground | Parking brake switch OFF (Switch pin pushed in) | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH) |
![]() |
Disconnect the A19 ECU connector.
Disconnect the A5 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A19-14 (PKB2) - A5-1 | Always | Below 1 Ω |
| A19-14 (PKB2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||