DTC C1713 Rear Height Control Sensor RH Circuit Malfunction |
DTC C1714 Rear Height Control Sensor LH Circuit Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| C1713 | With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear height control sensor RH is detected for 1 second. |
|
| C1714 | With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear height control sensor LH is detected for 1 second. |
|

| 1.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY |
![]() |
Check the rear height control sensor RH: (C1713).
Remove the rear height control sensor RH (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) end of the batteries to terminal 3 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 1 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 1 (SHG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Sensor Condition | Specified Condition |
| 1 (SHG) - 2 (SHRR) | High (45°) | 4.4 to 4.6 V |
| Normal (0°) | 2.3 to 2.6 V | |
| Low (-45°) | 0.4 to 0.6 V |
![]() |
Check the rear height control sensor LH: (C1714).
Remove the rear height control sensor LH (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) end of the batteries to terminal 3 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 1 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRL) and terminal 1 (SHG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Sensor Condition | Specified Condition |
| 1 (SHG) - 2 (SHRL) | High (45°) | 4.4 to 4.6 V |
| Normal (0°) | 2.3 to 2.6 V | |
| Low (-45°) | 0.4 to 0.6 V |
| Result | Proceed to |
| OK | A |
| NG (Rear height control sensor RH) | B |
| NG (Rear height control sensor LH) | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR - SUSPENSION CONTROL ECU) |
![]() |
Check the rear height control sensor RH: (C1713).
Disconnect the O19 ECU connector and z2 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z2-1 (SHG) - O19-18 (SGR2) | Always | Below 1 Ω |
| z2-2 (SHRR) - O19-16 (SHRR) | Always | Below 1 Ω |
| z2-3 (SHB) - O19-14 (SBR2) | Always | Below 1 Ω |
| z2-1 (SHG) or O19-18 (SGR2) - Body ground | Always | 10 kΩ or higher |
| z2-2 (SHRR) or O19-16 (SHRR) - Body ground | Always | 10 kΩ or higher |
| z2-3 (SHB) or O19-14 (SBR2) - Body ground | Always | 10 kΩ or higher |
![]() |
Check the rear height control sensor LH: (C1714).
Disconnect the O19 ECU connector and z1 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z1-1 (SHG) - O19-19 (SGL2) | Always | Below 1 Ω |
| z1-2 (SHRL) - O19-17 (SHRL) | Always | Below 1 Ω |
| z1-3 (SHB) - O19-15 (SBL2) | Always | Below 1 Ω |
| z1-1 (SHG) or O19-19 (SGL2) - Body ground | Always | 10 kΩ or higher |
| z1-2 (SHRL) or O19-17 (SHRL) - Body ground | Always | 10 kΩ or higher |
| z1-3 (SHB) or O19-15 (SBL2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||