Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1713    Rear Height Control Sensor RH Circuit Malfunction

DTC    C1714    Rear Height Control Sensor LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

A magnetic circuit installed on the shaft inside the height control sensor rotates around the linear IC. The linear IC outputs voltage corresponding to the level of magnetic strength generated by the magnetic circuit. As a result, voltage corresponding to the shaft rotation angle is supplied to the suspension control ECU.

DTC Code
Detection Condition
Trouble Area
C1713
With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear height control sensor RH is detected for 1 second.
  1. Wire harness or connector
  2. Rear height control sensor sub-assembly RH
  3. Suspension control ECU
C1714
With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear height control sensor LH is detected for 1 second.
  1. Wire harness or connector
  2. Rear height control sensor sub-assembly LH
  3. Suspension control ECU

WIRING DIAGRAM


C179515E01


INSPECTION PROCEDURE

1.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY


    C179494E01
  1. Check the rear height control sensor RH: (C1713).

    1. Remove the rear height control sensor RH (Click here).

    2. Connect 3 dry cell batteries of 1.5 V in series.

    3. Connect the positive (+) end of the batteries to terminal 3 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 1 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 1 (SHG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Sensor Condition
      Specified Condition
      1 (SHG) - 2 (SHRR)
      High (45°)
      4.4 to 4.6 V
      Normal (0°)
      2.3 to 2.6 V
      Low (-45°)
      0.4 to 0.6 V

      NOTICE:
      Do not apply a voltage of more than 6 V.



    C179494E02
  1. Check the rear height control sensor LH: (C1714).

    1. Remove the rear height control sensor LH (Click here).

    2. Connect 3 dry cell batteries of 1.5 V in series.

    3. Connect the positive (+) end of the batteries to terminal 3 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 1 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRL) and terminal 1 (SHG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Sensor Condition
      Specified Condition
      1 (SHG) - 2 (SHRL)
      High (45°)
      4.4 to 4.6 V
      Normal (0°)
      2.3 to 2.6 V
      Low (-45°)
      0.4 to 0.6 V

      NOTICE:
      Do not apply a voltage of more than 6 V.

      Result 
      Result
      Proceed to
      OK
      A
      NG (Rear height control sensor RH)
      B
      NG (Rear height control sensor LH)
      C



B
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (Click here)

C
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (Click here)
A


2.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR - SUSPENSION CONTROL ECU)


    C179516E01
  1. Check the rear height control sensor RH: (C1713).

    1. Disconnect the O16 ECU connector and z2 sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z2-1 (SHG) - O16-19 (SGR2)
      Always
      Below 1 Ω
      z2-2 (SHRR) - O16-24 (SHRR)
      Always
      Below 1 Ω
      z2-3 (SHB) - O16-20 (SBR2)
      Always
      Below 1 Ω
      z2-1 (SHG) or O16-19 (SGR2) - Body ground
      Always
      10 kΩ or higher
      z2-2 (SHRR) or O16-24 (SHRR) - Body ground
      Always
      10 kΩ or higher
      z2-3 (SHB) or O16-20 (SBR2) - Body ground
      Always
      10 kΩ or higher



    C179516E02
  1. Check the rear height control sensor LH: (C1714).

    1. Disconnect the O16 ECU connector and z1 sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z1-1 (SHG) - O16-21 (SGL2)
      Always
      Below 1 Ω
      z1-2 (SHRL) - O16-23 (SHRL)
      Always
      Below 1 Ω
      z1-3 (SHB) - O16-22 (SBL2)
      Always
      Below 1 Ω
      z1-1 (SHG) or O16-21 (SGL2) - Body ground
      Always
      10 kΩ or higher
      z1-2 (SHRL) or O16-23 (SHRL) - Body ground
      Always
      10 kΩ or higher
      z1-3 (SHB) or O16-22 (SBL2) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)