Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1747    Leveling Solenoid Valve Circuit Malfunction

for Preparation Click here


DESCRIPTION

The suspension control ECU opens the leveling solenoid valve (No. 2 height control valve) to lead the compressed air to the height control cylinder (pneumatic cylinder) and to raise the vehicle height.
The No. 2 height control valve consists of a leveling solenoid valve and a gate solenoid valve.
The leveling solenoid valve opens and closes the passage between the compressor and the height control cylinder (pneumatic cylinder).

DTC Code
Detection Condition
Trouble Area
C1747
When either of the following is detected:
  1. With the height control valve inactivated, an open signal of the height control valve is detected for 1 second or more.
  2. With the height control valve activated, a short signal of the valve is detected 8 times successively.
  1. Wire harness or connector
  2. Leveling solenoid valve (No.2 height control valve)
  3. Suspension control ECU

HINT:
  1. Once the ECU stores DTC C1747 in the memory, the vehicle height control is suspended until a normal signal is input to the ECU from the height control solenoid valves. However, control is resumed if the ignition switch is turned off, then to ON again.
  2. Malfunction in the leveling solenoid valve:
    The height control operation is suspended, and the height control indicator light does not change by operating the height control switch.


WIRING DIAGRAM


C179529E02


INSPECTION PROCEDURE

HINT:
  1. If DTC C1781 (ECU malfunction) and/or C1782 (power source circuit) is displayed, perform the inspection necessary for DTC C1781 (Click here) and/or C1782 (Click here) first.
  2. If DTC C1781 and the C1782 are output at the same time, perform the inspection necessary for DTC C1782 first.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR LEVELING SOLENOID)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Leveling Solenoid
    Leveling solenoid valve
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC Chart)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.INSPECT NO. 2 HEIGHT CONTROL VALVE SUB-ASSEMBLY (LEVELING SOLENOID VALVE)
  1. Turn the ignition switch off.



    C179498E02
  1. Disconnect Q4 solenoid valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (E) - 3 (RH+)
    20°C (68°F)
    10 to 14 Ω

  1. Connect the battery positive (+) lead to terminal 3 and the negative (-) lead to terminal 2 of the solenoid valve connector. Then check that the valve makes an operating sound.

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 2 HEIGHT CONTROL VALVE SUB-ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (LEVELING SOLENOID VALVE - ECU AND BODY GROUND)


    C179530E02
  1. Disconnect the O16 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q4-3 (RH+) - O16-9 (SLRR)
    Always
    Below 1 Ω
    Q4-3 (RH+) or O16-9 (SLRR) - Body ground
    Always
    10 kΩ or higher
    Q4-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)