Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL

BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL PAD


    C155468
  1. Install the brake pedal pad onto the brake pedal.



2. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY


    C154462
  1. Install the brake pedal support with the 4 nuts.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

  1. Install the No. 3 brake pedal bracket to the brake pedal support.



    C154461
  1. Temporarily install the brake pedal support, No. 3 brake pedal bracket and brake pedal lever with the bolt and nut.



    C154460E03
  1. Install the bolt to the No. 3 brake pedal bracket.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal and return spring mounting bracket of the No. 3 brake pedal bracket.

  1. Install the brake pedal return spring.

  1. Tighten the bolt and nut.

    Torque:
    23 N*m{ 239 kgf*cm , 17 ft.*lbf }



3. INSTALL PUSH ROD PIN
  1. Apply lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.

  1. Set the push rod clevis in place, insert the push rod pin from outside the vehicle and then install a new clip.

    NOTICE:
    After assembly, check that the pedal operates smoothly.



4. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER
  1. Install a new stop light switch mounting adjuster.



5. INSTALL STOP LIGHT SWITCH ASSEMBLY


F049043E05


  1. Install the stop light switch into the adjuster until it slightly touches the brake pedal.

    NOTICE:
    Do not depress the brake pedal.




      F049044E24
    1. Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      Do not tighten the stop light switch more than the torque specification.

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

  1. Check the stop light switch clearance.

    Stop light switch clearance:
    1.5 to 2.5 mm (0.059 to 0.098 in.)

  1. Connect the stop light switch connector to the stop light switch.



6. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT


    C154523
  1. Install the air duct with the bolt.



7. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. Attach the 2 claws to install the sensor.



    B229064
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



9. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.

  1. Attach the 3 claws to install the hood lock lever



10. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



11. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



12. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



13. CHECK BRAKE PEDAL HEIGHT


    C205252E01
  1. Check the brake pedal height.

    Standard pedal height from dash panel:
    179.9 to 189.9 mm (7.08 to 7.48 in.)

    NOTICE:
    Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

    If the pedal height is incorrect, check that there is no damage in the brake pedal, brake pedal lever, brake pedal bracket and dash panel.
    Even if there is damage, there is no problem if the reserve distance is within the standard value. If necessary, replace these parts.



14. CHECK PEDAL FREE PLAY


    C154467E01
  1. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.

  1. Push in the brake pedal until the beginning of the resistance is felt. Measure the distance as shown in the illustration.

    Standard pedal free play:
    1.0 to 6.0 mm (0.0394 to 0.236 in.)



15. CHECK PEDAL RESERVE DISTANCE
  1. Release the parking brake pedal.



    R000934E23
  1. With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

    Standard pedal reserve distance from asphalt sheet at 490 N (50 kgf, 110.2 lbf):
    More than 104 mm (4.09 in.)

    If incorrect, troubleshoot the brake system (Click here).



16. CHECK MASTER CYLINDER PRESSURE SENSOR SIGNAL
  1. Check the master cylinder pressure sensor signal (Click here).