Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > One or more Power Seat Motors do not Operate

for Preparation Click here


DESCRIPTION

When the front power seat switch is operated, a command signal is sent to the position control ECU. The position control ECU then controls the appropriate seat motor as needed. The position control ECU is designed so that a malfunction of the seat memory system will not interfere with manual seat control.

WIRING DIAGRAM


B188601E01


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FRONT POWER SEAT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Driver Seat / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Driver Seat 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Reclining Rear
    Reclining switch signal (Rearward) / ON or OFF
    ON: Reclining switch (Rearward) on
    OFF: Reclining switch (Rearward) off
    -
    Reclining Front
    Reclining switch signal (Forward) / ON or OFF
    ON: Reclining switch (Forward) on
    OFF: Reclining switch (Forward) off
    -
    Front Vertical Down
    Front vertical switch signal (Downward) / ON or OFF
    ON: Front vertical switch (Downward) on
    OFF: Front vertical switch (Downward) off
    -
    Front Vertical Up
    Front vertical switch signal (Upward) / ON or OFF
    ON: Front vertical switch (Upward) on
    OFF: Front vertical switch (Upward) off
    -
    Lifter Switch Down
    Lifter switch signal (Downward) / ON or OFF
    ON: Lifter switch (Downward) on
    OFF: Lifter switch (Downward) off
    -
    Lifter Switch Up
    Lifter switch signal (Upward) / ON or OFF
    ON: Lifter switch (Upward) on
    OFF: Lifter switch (Upward) off
    -
    Slide Rear
    Sliding switch signal (Rearward) / ON or OFF
    ON: Sliding switch (Rearward) on
    OFF: Sliding switch (Rearward) off
    -
    Slide Front
    Sliding switch signal (Forward) / ON or OFF
    ON: Sliding switch (Forward) on
    OFF: Sliding switch (Forward) off
    -

    OK:
    On the intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
REPLACE FRONT POWER SEAT SWITCH LH (Click here)
OK


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Driver Seat / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Seat Reclining
    Seat reclining operation
    Front/OFF/Rear
    -
    Front Vertical Operation
    Seat front vertical operation
    Up/OFF/Down
    -
    Lifter Operation
    Seat lifter operation
    Up/OFF/Down
    -
    Seat Slide Operation
    Seat sliding operation
    Front/OFF/Rear
    -

OK:
The power seat motors operate normally.



NG
Go to step 3
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

3.INSPECT FRONT SEAT ASSEMBLY LH (POWER SEAT MOTOR)
  1. Remove the front seat assembly LH (Click here).



  1. Check operation of the sliding motor.



      B220959E01
    1. Check if the seat moves smoothly when the battery is connected to the sliding motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Forward
      Battery positive (+) → 2
      Battery negative (-) → 1
      Rearward



  1. Check operation of the reclining motor.



      B220959E02
    1. Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Forward
      Battery positive (+) → 1
      Battery negative (-) → 2
      Rearward



  1. Check operation of the front vertical motor.



      B220959E03
    1. Check if the seat moves smoothly when the battery is connected to the front vertical motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Upward
      Battery positive (+) → 2
      Battery negative (-) → 1
      Downward



  1. Check operation of the lifter motor.



      B220959E04
    1. Check if the seat moves smoothly when the battery is connected to the lifter motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Upward
      Battery positive (+) → 1
      Battery negative (-) → 2
      Downward



NG
REPLACE FRONT SEAT ASSEMBLY LH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - POWER SEAT MOTOR)


    B128944E05
  1. Disconnect the X10 switch connector.

  1. Disconnect the X5, X6, X7 and X8 motor connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X10-2 (SLD+) - X5-1
    Always
    Below 1 Ω
    X10-2 (SLD+) or X5-1 - Body ground
    Always
    10 kΩ or higher
    X10-3 (SLD-) - X5-2
    Always
    Below 1 Ω
    X10-3 (SLD-) or X5-2 - Body ground
    Always
    10 kΩ or higher
    X10-4 (FRV-) - X6-2
    Always
    Below 1 Ω
    X10-4 (FRV-) or X6-2 - Body ground
    Always
    10 kΩ or higher
    X10-6 (FRV+) - X6-1
    Always
    Below 1 Ω
    X10-6 (FRV+) or X6-1 - Body ground
    Always
    10 kΩ or higher
    X10-7 (LFT+) - X7-2
    Always
    Below 1 Ω
    X10-7 (LFT+) or X7-2 - Body ground
    Always
    10 kΩ or higher
    X10-8 (RCL+) - X8-2
    Always
    Below 1 Ω
    X10-8 (RCL+) or X8-2 - Body ground
    Always
    10 kΩ or higher
    X10-9 (LFT-) - X7-1
    Always
    Below 1 Ω
    X10-9 (LFT-) or X7-1 - Body ground
    Always
    10 kΩ or higher
    X10-10 (RCL-) - X8-1
    Always
    Below 1 Ω
    X10-10 (RCL-) or X8-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)