AUDIO AND VISUAL SYSTEM > Speaker Circuit (Built-in Amplifier) |

| 1.CHECK SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Malfunction in front speaker area | A |
| Malfunction in rear speaker area | B |
|
| ||||
| A | |
| 2.CHECK FRONT SIDE SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Front No. 2 speaker assembly | A |
| Front No. 1 speaker assembly | B |
|
| ||||
| A | |
| 3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the I11*1 and I13*2 speaker connectors.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (TWL+) | Always | Below 1 Ω |
| 2 (-) - 4 (TWL-) | ||
| 3 (TWL+) - 4 (TWL-) | Always | 3.2 to 4.6 Ω |
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (TWR+) | Always | Below 1 Ω |
| 2 (-) - 4 (TWR-) | ||
| 3 (TWR+) - 4 (TWR-) | Always | 3.2 to 4.6 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
![]() |
Disconnect the I1 radio receiver assembly connector.
Disconnect the I11*1 and I13*2 speaker connectors.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I1-2 (FL+) - I13-3 (TWL+) | Always | Below 1 Ω |
| I1-6 (FL-) - I13-4 (TWL-) | ||
| I1-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I1-6 (FL-) - Body ground |
| Tester Connection | Condition | Specified Condition |
| I1-1 (FR+) - I11-3 (TWR+) | Always | Below 1 Ω |
| I1-5 (FR-) - I11-4 (TWR-) | ||
| I1-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I1-5 (FR-) - Body ground |
|
| ||||
| OK | ||
| ||
| 5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the L8*1 and M10*2 speaker connectors.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
![]() |
Disconnect the L8*1, M10*2, I11*1 and I13*2 speaker connectors.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I13-1 (+) - M10-1 | Always | Below 1 Ω |
| I13-2 (-) - M10-2 | ||
| I13-1 (+) - Body ground | Always | 10 kΩ or higher |
| I13-2 (-) - Body ground |
| Tester Connection | Condition | Specified Condition |
| I11-1 (+) - L8-1 | Always | Below 1 Ω |
| I11-2 (-) - L8-2 | ||
| I11-1 (+) - Body ground | Always | 10 kΩ or higher |
| I11-2 (-) - Body ground |
|
| ||||
| OK | ||
| ||
| 7.CHECK REAR SIDE SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Quarter side speaker assembly | A |
| Rear No. 1 speaker assembly | B |
|
| ||||
| A | |
| 8.INSPECT QUARTER SIDE SPEAKER ASSEMBLY |
![]() |
Disconnect the O37*1 and O31*2 speaker connectors.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (+) | Always | Below 1 Ω |
| 2 (-) - 4 (-) | ||
| 1 (+) - 2 (-) | Always | 3.6 to 4.4 Ω |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - QUARTER SIDE SPEAKER ASSEMBLY) |
![]() |
Disconnect the I2 radio receiver assembly connector.
Disconnect the O37*1 and O31*2 speaker connectors.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I2-2 (RL+) - O31-1 (+) | Always | Below 1 Ω |
| I2-6 (RL-) - O31-2 (-) | ||
| I2-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I2-6 (RL-) - Body ground |
| Tester Connection | Condition | Specified Condition |
| I2-1 (RR+) - O37-1 (+) | Always | Below 1 Ω |
| I2-3 (RR-) - O37-2 (-) | ||
| I2-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I2-3 (RR-) - Body ground |
|
| ||||
| OK | ||
| ||
| 10.INSPECT REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the N1*1 and N7*2 speaker connectors.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (QUARTER SIDE SPEAKER ASSEMBLY - REAR NO. 1 SPEAKER ASSEMBLY) |
![]() |
Disconnect the N1*1, N7*2, O37*1 and O31*2 speaker connectors.
*1: for RH
*2: for LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O31-3 (+) - N7-1 | Always | Below 1 Ω |
| O31-4 (-) - N7-2 | ||
| O31-3 (+) - Body ground | Always | 10 kΩ or higher |
| O31-4 (-) - Body ground |
| Tester Connection | Condition | Specified Condition |
| O37-3 (+) - N1-1 | Always | Below 1 Ω |
| O37-4 (-) - N1-2 | ||
| O37-3 (+) - Body ground | Always | 10 kΩ or higher |
| O37-4 (-) - Body ground |
|
| ||||
| OK | ||
| ||