Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC Code
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Speakers
  2. Harness or connector
  3. Radio and display receiver assembly

WIRING DIAGRAM


E282458E06


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Disconnect the I55 and I56 radio and display receiver assembly connectors.

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the I55 and I56 radio and display receiver assembly connectors.

  1. Disconnect the L8*1 and/or M10*2 front No. 1 speaker assembly connector.

  1. Disconnect the I11*1 and/or I13*2 front No. 2 speaker assembly connector.

  1. Disconnect the L1*1 and/or M1*2 front No. 3 speaker assembly connector.

  1. Disconnect the N1*1 and/or N7*2 rear No. 1 speaker assembly connector.

  1. Disconnect the N2*1 and/or N8*2 rear No. 2 speaker assembly connector.

  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH side:
    Tester Connection
    Condition
    Specified Condition
    I55-1 (FR+) - I11-3 (TWR+)
    Always
    Below 1 Ω
    I55-5 (FR-) - I11-4 (TWR-)
    Always
    Below 1 Ω
    I55-1 (FR+) - L8-1
    Always
    Below 1 Ω
    I55-5 (FR-) - L8-2
    Always
    Below 1 Ω
    I11-1 (+) - L1-3
    Always
    Below 1 Ω
    I11-2 (-) - L1-1
    Always
    Below 1 Ω
    I56-1 (RR+) - O37-1 (+)
    Always
    Below 1 Ω
    I56-3 (RR-) - O37-2 (-)
    Always
    Below 1 Ω
    I56-1 (RR+) - N1-1
    Always
    Below 1 Ω
    I56-3 (RR-) - N1-2
    Always
    Below 1 Ω
    O37-3 (+) - N2-3
    Always
    Below 1 Ω
    O37-4 (-) - N2-1
    Always
    Below 1 Ω
    I55-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I55-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    I11-1 (+) - Body ground
    Always
    10 kΩ or higher
    I11-2 (-) - Body ground
    Always
    10 kΩ or higher
    I56-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I56-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    O37-3 (+) - Body ground
    Always
    10 kΩ or higher
    O37-4 (-) - Body ground
    Always
    10 kΩ or higher
    for LH side:
    Tester Connection
    Condition
    Specified Condition
    I55-2 (FL+) - I13-3 (TWL+)
    Always
    Below 1 Ω
    I55-6 (FL-) - I13-4 (TWL-)
    Always
    Below 1 Ω
    I55-2 (FL+) - M10-1
    Always
    Below 1 Ω
    I55-6 (FL-) - M10-2
    Always
    Below 1 Ω
    I13-1 (+) - M1-3
    Always
    Below 1 Ω
    I13-2 (-) - M1-1
    Always
    Below 1 Ω
    I56-2 (RL+) - O31-1 (+)
    Always
    Below 1 Ω
    I56-6 (RL-) - O31-2 (-)
    Always
    Below 1 Ω
    I56-2 (RL+) - N7-1
    Always
    Below 1 Ω
    I56-6 (RL-) - N7-2
    Always
    Below 1 Ω
    O31-3 (+) - N8-3
    Always
    Below 1 Ω
    O31-4 (-) - N8-1
    Always
    Below 1 Ω
    I55-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I55-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    I13-1 (+) - Body ground
    Always
    10 kΩ or higher
    I13-2 (-) - Body ground
    Always
    10 kΩ or higher
    I56-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I56-6 (RL-) - Body ground
    Always
    10 kΩ or higher
    O31-3 (+) - Body ground
    Always
    10 kΩ or higher
    O31-4 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 5
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

5.CHECK FRONT NO. 3 SPEAKER ASSEMBLY
  1. Replace the front No. 3 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 6
OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE) 

6.INSPECT REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly (Click here)

  1. Inspect the rear No. 1 speaker assembly (Click here).



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


7.CHECK REAR NO. 2 SPEAKER ASSEMBLY
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left rear speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 8
OK

END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

8.CHECK QUARTER SIDE SPEAKER ASSEMBLY
  1. Replace the quarter side speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left quarter speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (QUARTER SIDE SPEAKER ASSEMBLY IS DEFECTIVE)