Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SYSTEM

CLIMATE CONTROL SEAT SYSTEM > Climate Control Seat System does not Operate

for Preparation Click here


DESCRIPTION

The air conditioning amplifier assembly receives seat heater switch position signals when the ignition switch ON, and then transmits airflow amount signals to each seat climate blower.

WIRING DIAGRAM


B188621E01


INSPECTION PROCEDURE

1.CHECK CLIMATE CONTROL SEAT SYSTEM OPERATION
  1. Check if the climate control seat system operates normally.
    Result 
    Result
    Proceed to
    Climate control does not operate on both driver and passenger sides
    A
    Climate control does not operate on driver side
    B
    Climate control does not operate on front passenger side
    C



B
Go to step 5

C
Go to step 13
A


2.INSPECT FUSE (LH-IG, SEAT-HTR)


    B188612E02
  1. Remove the LH-IG and SEAT-HTR fuses from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    LH-IG fuse
    Always
    Below 1 Ω
    SEAT-HTR fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH - BATTERY)


    B193663E01
  1. Disconnect the H47 and H49 switch connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H47-8 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    H49-12 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL BLOWER - BATTERY)


    B191599E03
  1. Disconnect the X13 and W16 blower connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    X13-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    W16-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL BLOWER LH - BATTERY AND BODY GROUND)


    B191599E04
  1. Disconnect the X13 blower connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    X13-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X13-4 (GND) - Body ground
    Always
    Below 1 Ω



    B191600E03
  1. Disconnect the X14 blower connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X14-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER LH - SEATBACK CLIMATE CONTROL BLOWER LH)
B218386E01
  1. Disconnect the X13 blower connector.

  1. Disconnect the X14 blower connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X13-2 (CTB) - X14-2 (IG)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK SEAT CLIMATE CONTROL BLOWER LH


    B191601E03
  1. Check the input signal waveform.

    1. Connect an oscilloscope to terminal X13-3 (SIGN) and body ground with the climate control blower connector still connected.

    2. Check the signal waveform according to the condition(s) in the table below.
      Standard Condition 
      Tester Connection
      Tool Setting
      Condition
      X13-3 (SIGN) - Body ground
      2 V/DIV., 500 μsec/DIV.
      Ignition switch ON
      Seat heater switch blower side volume 3

      OK:
      The waveform is displayed as shown in the illustration.

Result 
Result
Proceed to
NG
A
OK (Seat cushion blower side)
B
OK (Seatback blower side)
C


B
REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER LH (Click here)

C
Go to step 12
A


8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - SEAT CLIMATE CONTROL BLOWER LH)


    B191602E01
  1. Disconnect the H67 amplifier connector.

  1. Disconnect the X13 blower connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H67-9 (SHD+) - X13-3 (SIGN)
    Always
    Below 1 Ω
    H67-9 (SHD+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH LH - BATTERY AND BODY GROUND)


    B191603E01
  1. Disconnect the H47 switch connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H47-3 (E) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H47-8 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT SEAT HEATER SWITCH LH


    B191604E01
  1. Remove the seat heater switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (BLLH) - 4 (SW-)
    Seat Heater switch off
    1.54 to 2.86 kΩ
    Seat heater switch blower side volume 3
    Below 0.1 kΩ



NG
REPLACE SEAT HEATER SWITCH LH (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH LH - AIR CONDITIONING AMPLIFIER)


    B191605E01
  1. Disconnect the H67 amplifier connector.

  1. Disconnect the H47 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H47-4 (SW-) - H67-6 (SG-5)
    Always
    Below 1 Ω
    H47-4 (SW-) - Body ground
    Always
    10 kΩ or higher
    H47-5 (BLLH) - H67-15 (AD-4)
    Always
    Below 1 Ω
    H47-5 (BLLH) - Body ground
    Always
    10 kΩ or higher
    H47-10 (SW+) - H67-8 (S5-2)
    Always
    Below 1 Ω
    H47-10 (SW+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

12.CHECK SEATBACK CLIMATE CONTROL BLOWER LH (OPERATION)
  1. After replacing the seatback climate control blower LH, check that the climate control seat functions operate normally.

    OK:
    Climate control seat functions operate normally.



NG
REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER LH (Click here)
OK

END (REPLACE SEATBACK CLIMATE CONTROL BLOWER LH) (Click here)  

13.CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL BLOWER RH - BATTERY AND BODY GROUND)


    B191599E02
  1. Disconnect the W16 blower connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W16-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W16-4 (GND) - Body ground
    Always
    Below 1 Ω



    B191600E04
  1. Disconnect the W17 blower connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W17-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE CONTROL BLOWER RH - SEATBACK CLIMATE CONTROL BLOWER RH)
B218386E02
  1. Disconnect the W16 blower connector.

  1. Disconnect the W17 blower connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W16-2 (CTB) - W17-2 (IG)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15.CHECK SEAT CLIMATE CONTROL BLOWER RH


    B191601E04
  1. Check the input signal waveform.

    1. Connect an oscilloscope to terminal W16-3 (SIGN) and body ground with the climate control blower connector still connected.

    2. Check the signal waveform according to the condition(s) in the table below.
      Standard Condition 
      Tester connection
      Tool Setting
      Condition
      W16-3 (SIGN) - Body ground
      2 V/DIV., 500 μsec/DIV.
      Ignition switch ON
      Seat heater switch blower side volume 3

      OK:
      The waveform is displayed as shown in the illustration.

Result 
Result
Proceed to
NG
A
OK (Seat cushion blower side)
B
OK (Seatback blower side)
C


B
REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER RH (Click here)

C
Go to step 20
A


16.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - SEAT CLIMATE CONTROL BLOWER RH)


    B191602E02
  1. Disconnect the H67 amplifier connector.

  1. Disconnect the W16 blower connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H67-10 (SHP+) - W16-3 (SIGN)
    Always
    Below 1 Ω
    H67-10 (SHP+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH RH - BATTERY AND BODY GROUND)


    B191606E01
  1. Disconnect the H49 switch connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H49-3 (E) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H49-12 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18.INSPECT SEAT HEATER SWITCH RH


    B191607E01
  1. Remove the seat heater switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (BLRH) - 6 (SVSG)
    Seat Heater switch OFF
    1.54 to 2.86 kΩ
    Seat heater switch blower side volume 3
    Below 0.1 kΩ



NG
REPLACE SEAT HEATER SWITCH RH (Click here)
OK


19.CHECK HARNESS AND CONNECTOR (SEAT HEATER SWITCH RH - AIR CONDITIONING AMPLIFIER)


    B191608E01
  1. Disconnect the H67 amplifier connector.

  1. Disconnect the H49 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H49-6 (SVSG) - H67-6 (SG- 5)
    Always
    Below 1 Ω
    H49-6 (SVSG) - Body ground
    Always
    10 kΩ or higher
    H49-7 (BLRH) - H67-16 (AD-5)
    Always
    Below 1 Ω
    H49-7 (BLRH) - Body ground
    Always
    10 kΩ or higher
    H49-14 (SVS5) - H67-8 (S5-2)
    Always
    Below 1 Ω
    H49-14 (SVS5) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

20.CHECK SEATBACK CLIMATE CONTROL BLOWER RH (OPERATION)
  1. After replacing the seatback climate control blower RH, check that the climate control seat functions operate normally.

    OK:
    Climate control seat functions operate normally.



NG
REPLACE SEAT CUSHION CLIMATE CONTROL BLOWER RH (Click here)
OK

END (REPLACE SEATBACK CLIMATE CONTROL BLOWER RH) (Click here)