Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1340/47    Center Differential Lock Circuit

for Preparation Click here


DESCRIPTION

When the vehicle is changed to 4WD (L4 mode) and the center differential locks, VSC control turns off and the VSC OFF indicator light illuminates.

DTC Code
DTC Detection Condition
Trouble Area
C1340/47
When the terminal IG1 voltage is between 10 and 14 V, there is an open in the center differential lock detection switch circuit or there is a transfer mechanical malfunction for 5 seconds or more.
  1. Center differential lock detection switch
  2. Center differential lock detection switch circuit
  3. 4WD control ECU
  4. VSC actuator (skid control ECU)

WIRING DIAGRAM


C193649E04


INSPECTION PROCEDURE

NOTICE:
When replacing the VSC actuator assembly, perform zero point calibration (Click here).

HINT:
If the transfer shift actuator cannot change from 2WD to 4WD or 4WD to 2WD or cannot lock the center differential, inspect and repair the touch select 2-4 and high-low systems first.

1.INSPECT SKID CONTROL ECU (EXI2 TERMINAL)
  1. Set the vehicle in the 4WD with center differential locked state using the center differential lock detection switch.



    C240470E05
  1. Disconnect the A19 skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A19-11 (EXI2) - Body ground
    1. Ignition switch ON
    2. 4WD with center differential locked (Center differential lock detection switch ON)
    Below 1.5 V

  1. Connect the A19 skid control ECU connector.

  1. Set the vehicle in the 2WD or 4WD with center differential free state using the center differential lock detection switch.

  1. Disconnect the A19 skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A19-11 (EXI2) - Body ground
    1. Ignition switch ON
    2. 2WD or 4WD with center differential free (Center differential lock detection switch OFF)
    10 to 14 V



NG
Go to step 2
OK

REPLACE VSC ACTUATOR ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4WD CONTROL ECU)


    C240473E01
  1. Confirm that the skid control ECU connector and 4WD control ECU connector are properly connected.

  1. Disconnect the A19 skid control ECU connector.

  1. Disconnect the A28 4WD control ECU connector.

  1. Disconnect the D45 transfer shift actuator connector.

  1. Inspect both the connector case and terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A19-11 (EXI2) - A28-14 (4WD)
    Always
    Below 1 Ω
    A19-11 (EXI2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BODY GROUND)


  1. Confirm that the 4WD control ECU connector and transfer shift actuator connectors are properly connected.


    C159461E05

  1. Disconnect the A28 4WD control ECU connector.

  1. Inspect the connector case and terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Connect the A28 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A28-14 (4WD) - Body ground
    4WD with center differential locked
    (Center differential lock detection switch ON)
    Below 1 Ω
    2WD or 4WD with center differential free
    (Center differential lock detection switch OFF)
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Check if the same DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A

REPLACE 4WD CONTROL ECU (Click here)