Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL > REPLACEMENT

for Preparation Click here


HINT:
The procedure described below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. DRAIN DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, remove the filler plug and gasket.

    2. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.

    3. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. for Rear Differential:

    1. Using a 10 mm hexagon wrench, remove the filler plug and gasket.

    2. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.

    3. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.

      Torque:
      65 N*m{ 660 kgf*cm , 48 ft.*lbf }



2. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
  1. Remove the front drive shaft (Click here).



3. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C181011E01
  1. Using SST, tap out the 2 oil seals.

    SST
    09308-10010  



4. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL
  1. Apply MP grease to 2 new oil seals.



    C181006E02
  1. Using SST and a hammer, tap in the 2 oil seals.

    SST
    09223-15020  
    09950-70010   (09951-07150)

    NOTICE:
    Make sure that the oil seal are installed in the proper locations.

    Standard oil seal depth:
    -0.50 to 0.50 mm (-0.0197 to 0.0197 in.)



5. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Install the front drive shaft (Click here).



6. ADD DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil Type:
    Item
    Oil Type and Viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front Differential Capacity:
    Specified Condition
    2.00 to 2.10 liters (2.1 to 2.2US qts., 1.7 to 1.8 Imp. qts.)

    Rear Differential Capacity:
    Specified Condition
    1.50 to 1.60 liters (1.6 to 1.7 US qts., 1.3 to 1.4 Imp. qts.)

  1. for Rear Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }