GENERATOR > INSTALLATION |
| 1. INSTALL GENERATOR ASSEMBLY (for 150 A Type) |
![]() |
Install the generator with the 3 bolts and nut.
![]() |
Connect the generator connector.
Connect the generator wire with the nut.
Install the terminal cap.
Install the harness bracket to the generator with the bolt.
| 2. INSTALL GENERATOR ASSEMBLY (for 180 A Type) |
![]() |
Install the generator with the 3 bolts and nut.
![]() |
Connect the generator connector.
Connect the generator wire with the nut.
Install the terminal cap.
Install the harness bracket to the generator with the bolt.
| 3. CONNECT VANE PUMP ASSEMBLY |
![]() |
![]() |
Install the vane pump to the timing chain cover with the 2 bolts.
![]() |
Connect the clamp and 2 power steering connectors.
| 4. INSTALL FRONT FENDER APRON SEAL RH |
Install the fender apron seal with the 6 clips.
| 5. INSTALL FAN SHROUD |
![]() |
Install the fan pulley to the fan bracket.
Place the shroud together with the coupling fan between the radiator and engine.
Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the shroud claws to the radiator as shown in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the upper radiator tank.
![]() |
Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.
Install the fan and generator V belt .
Tighten the 4 nuts of the fluid coupling fan.
| 6. CONNECT OUTLET RADIATOR HOSE |
![]() |
Connect the outlet radiator hose to the water inlet housing.
| 7. INSTALL INLET RADIATOR HOSE |
![]() |
Install the inlet radiator hose.
| 8. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 9. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 10. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Attach the 2 V-bank cover hooks to the No. 1 V-bank cover bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover sub-assembly to attach the pins.
| *1 | V-bank Cover Grommet |
| *2 | Pin |
| *3 | No. 1 V-bank Cover Bracket |
| *4 | V-bank Cover Hook |
| 11. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |