Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Manual Up / Down Function does not Operate on Back Door Only

for Preparation Click here


DESCRIPTION

If the back door power window does not operate, the retract switch in the rear wiper motor, the back door power window motor or the wire harness may be abnormal.

WIRING DIAGRAM


B178357E01


INSPECTION PROCEDURE

1.CHECK REAR WIPER OPERATION
  1. Turn the ignition switch to ON.

  1. Turn the rear wiper switch on.

  1. Turn the rear wiper switch off.

  1. Check that the rear wiper stops at the retract position when the rear wiper switch is turned off.

    OK:
    The rear wiper arm returns to the correct position.



NG
REPAIR OR REPLACE REAR WIPER MOTOR ASSEMBLY (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (WIPER RETRACTED POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Back Door P/W / Data List.

  1. According to the display on the intelligent tester, read the "Data List".

    Back Door P/W 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Wiper Retracted position
    Rear wiper retract switch signal / ON or OFF
    ON: Rear wiper retract switch is in ON position
    OFF: Rear wiper retract switch is in OFF position
    -

OK:
The intelligent tester display changes normally when rear wiper motor is operated.



NG
Go to step 8
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BACK DOOR POWER WINDOW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Back Door P/W / Active Test.

  1. According to the display on the intelligent tester, perform the "Active Test".

    Back Door P/W 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Back Door Power Window
    Back Door Power Window
    OFF/UP/DOWN
    -

    OK:
    Back door power window opens and closes.



NG
Go to step 6
OK


4.INSPECT BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B191468E01
  1. Remove the back door power window regulator switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (E) - 6(UP) - 7(A-UP)
    Auto UP
    Below 1 Ω
    2 (E) - 6(UP)
    UP
    Below 1 Ω
    2 (E) - 4 (DOWN)
    DOWN
    Below 1 Ω
    2 (E) - 3 (A-DN) - 4 (DOWN)
    Auto DOWN
    Below 1 Ω
    2 (E) - Each connectors
    OFF
    10 kΩ or higher



NG
REPLACE BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (BACK DOOR POWER WINDOW REGULATOR SWITCH - BODY GROUND)


    B191449E01
  1. Disconnect the H9 back door power window regulator switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H9-2 (E) - Body Ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BACK DOOR ECU - BACK DOOR P/W REGULATOR SWITCH) 

6.INSPECT BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B194351E02
  1. Remove the back door regulator motor assembly .

  1. Apply battery voltage between the connector terminals and check that the motor gear rotates smoothly.

    Standard:
    Tester Connection
    Specified Condition
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear counterclockwise
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear clockwise

    NOTICE:
    Do not apply battery voltage to any terminals except terminals 1 and 2.



NG
REPLACE BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY
OK


7.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - BACK DOOR POWER WINDOW MOTOR)


    B191450E01
  1. Disconnect the V3 back door ECU connector.

  1. Disconnect the V4 back door regulator motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V3-5 (BDUP) - V4-1 (UP)
    Always
    Below 1 Ω
    V3-6 (BDDN) - V4-2 (DOWN)
    Always
    Below 1 Ω
    V3-5 (BDUP) - Body ground
    Always
    10 kΩ or higher
    V3-6 (BDDN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK DOOR ECU  

8.CHECK HARNESS AND CONNECTOR (BACK DOOR ECU - REAR WIPER MOTOR)


    B191451E01
  1. Disconnect the V3 back door ECU connector.

  1. Disconnect the V10 rear wiper motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V3-17 (P) - V10-1 (P)
    Always
    Below 1 Ω
    V3-25 (SGND) - V10-2 (E)
    Always
    Below 1 Ω
    V3-17 (P) - Body ground
    Always
    10 kΩ or higher
    V3-25 (SGND)- Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR WIPER MOTOR ASSEMBLY (Click here)