WINDOW DEFOGGER SYSTEM > Rear Window Defogger System does not Operate |

| 1.PERFORM INITIALIZATION (BACK DOOR POWER WINDOW) |
Initialize the back door power window regulator motor (Click here)
Check if rear window defogger function operate (Click here)
|
| ||||
| OK | ||
| ||
| 2.CHECK LIN COMMUNICATION SYSTEM |
Check for LIN communication system DTCs related to the power window control system (Click here).
|
| ||||
| OK | |
| 3.CHECK CAN COMMUNICATION SYSTEM |
Check for CAN communication system DTCs (Click here).
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DEFOG RELAY) |
Select the Active Test using the intelligent tester to generate a control command, and then check that the rear window defogger operates.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Defogger Relay (Rear) | Rear window defogger relay operation | OFF or ON | - |
|
| ||||
| OK | |
| 5.CHECK AIR CONDITIONING SYSTEM (LIN COMMUNICATION) |
Operate the front air conditioner control panel to change the set temperature and check that the temperature at the outlets changes.
|
| ||||
| OK | |
| 6.REPLACE INTEGRATION CONTROL AND PANEL |
Temporarily replace the integration control and panel with a new or normally functioning one (Click here).
| NEXT | |
| 7.CHECK INTEGRATION CONTROL AND PANEL (OPERATION) |
Check that the malfunction disappears.
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (DEFOG RELAY - BACK DOOR GLASS [REAR WINDOW DEFOGGER]) |
![]() |
Disconnect the V11 rear defogger connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| V11-1(B) - Body ground | Engine running Rear defogger switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS [REAR WINDOW DEFOGGER] - BODY GROUND) |
![]() |
Disconnect the V12 rear defogger connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| V12-1(E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 10.INSPECT DEFOG RELAY |
![]() |
Remove the DEFOG relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 4 | When battery voltage is not applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | 10 kΩ or higher | |
| 3 - 4 | When battery voltage is applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (DEFOG RELAY - BATTERY) |
![]() |
Remove the DEFOG relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| DEFOG relay terminal 1 - Body ground | Ignition switch ON | 11 to 14 V |
| DEFOG relay terminal 5 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (DEFOG RELAY - AIR CONDITIONING AMPLIFIER) |
![]() |
Remove the DEFOG relay from the engine room relay block.
Disconnect the H24 air conditioning amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| DEFOG relay terminal 2 - H24-38 (RDEF) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS [REAR WINDOW DEFOGGER] - DEFOG RELAY AND BODY GROUND) |
![]() |
Disconnect the V11 defogger connectors.
Remove the DEFOG relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| V11-1 (B) - DEFOG relay terminal 3 | Always | Below 1 Ω |
| DEFOG relay terminal 4 - Body ground | Always | Below 1 Ω |
| V11-1 (B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||