Home › Vehicle Interior › SEAT BELT › FRONT SEAT INNER BELT ASSEMBLY

FRONT SEAT INNER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Manual Seat)
  1. Install the front seat belt anchor plate.



    B191256E02
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding part of the front seat adjuster.



    B191249
  1. Connect the connector and attach the 5 clamps.



2. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Power Seat)
  1. Install the front seat belt anchor plate.



    B191260E03
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding part of the front seat adjuster.



    B191250
  1. Connect the connector and attach the 5 clamps.



3. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (w/ Climate Control Seat System)
  1. Install the front seat belt anchor plate.



    B191260E02
  1. Install the front seat inner belt assembly LH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding part of the front seat adjuster.



    B191251
  1. Connect the connector and attach the 6 clamps.



4. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Manual Seat)
  1. Install the front seat belt anchor plate.



    B191258E02
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part of the front seat adjuster.



    B191252
  1. Attach the 3 clamps.



5. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Power Seat)
  1. Install the front seat belt anchor plate.



    B191262E02
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part of the front seat adjuster.



    B191253
  1. Connect the connector and attach the clamp.



6. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (w/ Climate Control Seat System)
  1. Install the front seat belt anchor plate.



    B191262E02
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part of the front seat adjuster.



    B191254
  1. Connect the connector and attach the clamp.



7. INSTALL FRONT SEAT CUSHION SHIELD INNER LH (for Manual Seat)


    B191000E01
  1. Attach the wire harness clamp.

  1. Attach the 3 claws in the order shown in the illustration, to install the cushion shield.

  1. Install the screw.



8. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Install the front seat assembly LH (Click here).



9. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Install the front seat assembly LH (Click here).



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).