Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1630/23    Driver Side Rear Airbag Sensor Circuit Malfunction

DTC    B1635/24    Front Passenger Side Rear Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The rear airbag sensor LH or RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1630/23 or B1635/24 is stored when a malfunction is detected in the rear airbag sensor LH or RH circuit.

DTC Code
Detection Condition
Trouble Area
B1630/23
When one of following conditions is met:
  1. Rear airbag sensor LH malfunction
  2. Side airbag sensor LH malfunction
  3. Center airbag sensor malfunction
  1. Rear airbag sensor LH
  2. Side airbag sensor LH
  3. Center airbag sensor assembly
  4. Floor wire
  5. Front door wire LH
B1635/24
When one of following conditions is met:
  1. Rear airbag sensor RH malfunction
  2. Side airbag sensor RH malfunction
  3. Center airbag sensor malfunction
  1. Rear airbag sensor RH
  2. Side airbag sensor RH
  3. Center airbag sensor assembly
  4. No. 2 floor wire
  5. Front door wire RH

WIRING DIAGRAM


C179187E03


C179187E04


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1635/24 is output
    A
    DTC B1630/23 is output
    B
    DTC B1630/23 and B1635/24 are not output
    C



B
Go to step 8

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor RH and the rear airbag sensor RH.

OK:
The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Check that the connectors (on the side airbag sensor RH side and the rear airbag sensor RH side) are not damaged (Click here).

OK:
The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


4.CHECK REAR AIRBAG SENSOR RH CIRCUIT

C179619E01

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L9-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    L9-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector E.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-1 (BCR+) - L9-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-1 (BCR+) - L9-2 (BCR-)
    Always
    1 MΩ or higher
    L9-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    L9-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 7
OK


5.CHECK REAR AIRBAG SENSOR RH
C148441E08
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Interchange the rear airbag sensor RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result: 
    Result
    Proceed to
    DTC B1635/24 is output
    A
    DTC B1630/23 is output
    B
    DTC B1630/23 and B1635/24 are not output
    C

    HINT:
    Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not released to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



B
REPLACE REAR AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


6.CHECK SIDE AIRBAG SENSOR RH
C171827E13
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1635/24 is output (w/ Cool Box)
    A
    DTC B1635/24 is output (w/o Cool Box)
    B
    DTC B1630/23 is output
    C
    DTC B1630/23 and B1635/24 are not output
    D

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR RH (Click here)

D
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

7.CHECK FRONT DOOR WIRE RH (SIDE AIRBAG SENSOR RH - NO. 2 FLOOR WIRE)

C172034E09

  1. Disconnect the No. 2 floor wire connector from the door wire RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L9-1 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    L9-2 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-1 (BCR+) - L9-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L9-1 (BCR+) - L9-2 (BCR-)
    Always
    1 MΩ or higher
    L9-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    L9-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

8.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor LH and the rear airbag sensor LH.

OK:
The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


9.CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Check that the connectors (on the side airbag sensor LH side and the rear airbag sensor LH side) are not damaged (Click here).

OK:
The connectors are not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


10.CHECK REAR AIRBAG SENSOR LH CIRCUIT

C179619E02

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M11-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    M11-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.

  1. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector E.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-1 (BCL+) - M11-2 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-1 (BCL+) - M11-2 (BCL-)
    Always
    1 MΩ or higher
    M11-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    M11-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 13
OK


11.CHECK REAR AIRBAG SENSOR LH
C148441E02
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result: 
    Result
    Proceed to
    DTC B1630/23 is output
    A
    DTC B1635/24 is output
    B
    DTC B1630/23 and B1635/24 are not output
    C

    HINT:
    Codes other than DTC B1630/23 and B1635/24 may be output at this time, but they are not released to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.



B
REPLACE REAR AIRBAG SENSOR LH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


12.CHECK SIDE AIRBAG SENSOR LH
C180158E01
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1630/23 is output (w/ Cool Box)
    A
    DTC B1630/23 is output (w/o Cool Box)
    B
    DTC B1635/24 is output
    C
    DTC B1630/23 and B1635/24 are not output
    D

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR LH (Click here)

D
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

13.CHECK FRONT DOOR WIRE LH (SIDE AIRBAG SENSOR LH - FLOOR WIRE)

C172034E10

  1. Disconnect the floor wire connector from the door wire LH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M11-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    M11-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-1 (BCL+) - M11-2 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M11-1 (BCL+) - M11-2 (BCL-)
    Always
    1 MΩ or higher
    M11-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    M11-2 (BCL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FRONT DOOR WIRE LH
OK

REPLACE FLOOR WIRE