Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Power Mirrors do not Return to Memorized Position

for Preparation Click here


SYSTEM DESCRIPTION

When the seat memory switch 1 or seat memory switch 2 is pressed, the front power seat switch LH mirror position signal is sent through the CAN communication line to the outer mirror control ECU. The outer mirror control ECU then activates the mirror control motors to move the mirrors to the previously recorded positions.

WIRING DIAGRAM


B191617E02


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).
    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK POWER MIRROR CONTROL FUNCTION
  1. Check that the mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.

    OK:
    Mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.



NG
GO TO PROBLEM SYMPTOMS TABLE (POWER MIRROR CANNOT BE ADJUSTED WITH POWER MIRROR SWITCH) (Click here)
OK


3.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Mirror / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Mirror 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Mirror Memory No. 1
    Mirror position memorized in seat memory switch 1 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No. 2
    Mirror position memorized in seat memory switch 2 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -

    OK:
    On the intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
REPLACE OUTER MIRROR CONTROL ECU (Click here)
OK


4.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Mirror / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Mirror 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    RH Mir Position Sensor V
    Passenger side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    RH Mir Position Sensor H
    Passenger side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    LH Mir Position Sensor V
    Driver side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    LH Mir Position Sensor H
    Driver side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -

    OK:
    When mirror control switch is operated, voltage changes within range shown in above chart.

    Result 
    Result
    Proceed to
    LH side mirror does not operate normally
    A
    RH side mirror does not operate normally
    B
    Mirror operates normally
    C



B
Go to step 7

C
GO TO FRONT POWER SEAT CONTROL SYSTEM (Click here)
A


5.CHECK OUTER MIRROR CONTROL ECU


    B191616E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M8-2 (VC) - M8-3 (E1)
    Ignition switch ON
    3.5 to 5.5 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M8-3 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPLACE OUTER MIRROR CONTROL ECU (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)


    B193662E03
  1. Disconnect the M8 ECU connector.

  1. Disconnect the M5 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M5-15 (VC) - M8-2 (VC)
    Always
    Below 1 Ω
    M5-15 (VC) - Body ground
    Always
    10 kΩ or higher
    M5-16 (HSRL) - M8-5 (HSRL)
    Always
    Below 1 Ω
    M5-16 (HSRL) - Body ground
    Always
    10 kΩ or higher
    M5-17 (VSRL) - M8-4 (VSR)
    Always
    Below 1 Ω
    M5-17 (VSRL) - Body ground
    Always
    10 kΩ or higher
    M5-18 (E1) - M8-3 (E1)
    Always
    Below 1 Ω
    M5-18 (E1)- Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (Click here)  

7.CHECK OUTER MIRROR CONTROL ECU


    B191616E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M8-22 (VC) - M8-23 (E1)
    Ignition switch ON
    3.5 to 5.5 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M8-23 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPLACE OUTER MIRROR CONTROL ECU (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)


    B193662E07
  1. Disconnect the M8 ECU connector.

  1. Disconnect the L6 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L6-15 (VC) - M8-22 (VC)
    Always
    Below 1 Ω
    L6-15 (VC) - Body ground
    Always
    10 kΩ or higher
    L6-16 (HSSR) - M8-25 (HSRR)
    Always
    Below 1 Ω
    L6-16 (HSSR) - Body ground
    Always
    10 kΩ or higher
    L6-17 (VSSR) - M8-24 (VSRR)
    Always
    Below 1 Ω
    L6-17 (VSSR) - Body ground
    Always
    10 kΩ or higher
    L6-18 (E1) - M8-23 (E1)
    Always
    Below 1 Ω
    L6-18 (E1)- Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (Click here)