Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Reverse Shift-linked Function of Power Mirrors does not Operate

for Preparation Click here


SYSTEM DESCRIPTION

When the reverse signal is sent from the ECM through the CAN communication line to the outer mirror control ECU, the outer mirror control ECU activates the outer rear view mirror LH and RH reverse shift-linked function.

HINT:
The reverse shift-linked function will not occur when the outer mirror reverse gear link switch is not ON.


WIRING DIAGRAM


B193748E03


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).
    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (PARK/NEUTRAL POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    Shift SW Status (R Range)
    PNP switch status / ON or OFF
    ON: Shift lever in R
    OFF: Shift lever not in R
    -

    OK:
    On the intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
GO TO AUTOMATIC TRANSMISSION SYSTEM (PNP SWITCH CIRCUIT) (Click here)
OK


3.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Mirror / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Mirror 
    Tester Display
    Measurement Item/Display
    Normal Condition
    Diagnostic Note
    RH Mir Position Sensor V
    RH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -
    LH Mir Position Sensor V
    LH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V
    Within range from 0 to 5 V
    -

    OK:
    When mirror control switch is operated to turn mirror upward or downward, voltage changes within range shown in above chart.

    Result 
    Result
    Proceed to
    Neither mirror operates normally
    A
    LH side mirror does not operate normally
    B
    RH side mirror does not operate normally
    C
    Mirror operates normally
    D



B
Go to step 6

C
Go to step 8

D
REPLACE OUTER MIRROR CONTROL ECU (Click here)
A


4.INSPECT OUTER MIRROR REVERSE GEAR LINK SWITCH


    C155488E04
  1. Remove the switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 6
    Pressed
    Below 1 Ω
    Not pressed
    10 kΩ or higher



NG
REPLACE OUTER MIRROR REVERSE GEAR LINK SWITCH
OK


5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - OUTER MIRROR CONTROL ECU)


    B193749E02
  1. Disconnect the M8 ECU connector.

  1. Disconnect the H76 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H76-3 - Body ground
    Always
    Below 1 Ω
    M8-36 (AR) - H76-6
    Always
    Below 1 Ω
    M8-36 (AR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)  

6.CHECK OUTER MIRROR CONTROL ECU


    B191616E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M8-2 (VC) - M8-3 (E1)
    Ignition switch ON
    3.5 to 5.5 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M8-3 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPLACE OUTER MIRROR CONTROL ECU (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)


    B193662E05
  1. Disconnect the M8 ECU connector.

  1. Disconnect the M5 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M5-15 (VC) - M8-2 (VC)
    Always
    Below 1 Ω
    M5-15 (VC) - Body ground
    Always
    10 kΩ or higher
    M5-17 (VSRL) - M8-4 (VSR)
    Always
    Below 1 Ω
    M5-17 (VSRL) - Body ground
    Always
    10 kΩ or higher
    M5-18 (E1) - M8-3 (E1)
    Always
    Below 1 Ω
    M5-18 (E1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (Click here)  

8.CHECK OUTER MIRROR CONTROL ECU


    B191616E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M8-22 (VC) - M8-23 (E1)
    Ignition switch ON
    3.5 to 5.5 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M8-23 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPLACE OUTER MIRROR CONTROL ECU (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)


    B193662E08
  1. Disconnect the M8 ECU connector.

  1. Disconnect the L6 mirror connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L6-15 (VC) - M8-22 (VC)
    Always
    Below 1 Ω
    L6-15 (VC) - Body ground
    Always
    10 kΩ or higher
    L6-17 (VSSR) - M8-24 (VSRR)
    Always
    Below 1 Ω
    L6-17 (VSSR) - Body ground
    Always
    10 kΩ or higher
    L6-18 (E1) - M8-23 (E1)
    Always
    Below 1 Ω
    L6-18 (E1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (Click here)