Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > Headlight Cleaner Motor and Relay Circuit

for Preparation Click here


DESCRIPTION

This circuit provides power to the headlight cleaner control relay.
The headlight cleaner control relay sends the signal from the switch, etc. to the headlight cleaner motor to operate the headlight cleaner system.

WIRING DIAGRAM


E162516E03


INSPECTION PROCEDURE

1.INSPECT FUSE (ECU-IG No. 2, H-LP CLN)


    E160630E13
  1. Remove the ECU-IG No. 2 fuse from the main body ECU.

  1. Remove the H-LP CLN fuse from the engine junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG No. 2 fuse
    Always
    Below 1 Ω
    H-LP CLN fuse

  1. Reinstall the ECU-IG No. 2 fuse.

  1. Reinstall the H-LP CLN fuse.



NG
REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)


    E162510E01
  1. Disconnect the A32 headlight cleaner control relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A32-3 (IG) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A32-4 (E) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the headlight cleaner control relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
B172829E03
  1. Remove the headlight cleaner motor and pump assembly (Click here).

  1. Apply battery voltage to the headlight cleaner motor and pump assembly and check the operation of the headlight cleaner motor and pump assembly.

    OK:
    Measurement Connection
    Specified Condition
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 2
    Headlight cleaner motor operation is normal

  1. Reinstall the headlight cleaner motor and pump assembly.



NG
REPLACE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (CLEANER MOTOR - HEADLIGHT CLEANER CONTROL RELAY AND BATTERY)


    E125074E10
  1. Disconnect the A30 headlight cleaner motor and pump connector.

  1. Disconnect the A32 headlight cleaner control relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A30-1 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A30-2 - A32-6 (PB)
    Always
    Below 1 Ω
    A30-2 or A32-6 (PB) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the headlight cleaner motor and pump connector.

  1. Reconnect the headlight cleaner control relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)