DTC B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1655/37 | When one of following conditions is met:
|
|

| 1.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.
|
| ||||
| OK | |
| 2.CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and the front seat inner belt LH.
Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH) |

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O4-1 (LBE+) - Body ground | Ignition switch ON | Below 1 V |
| O4-3 (LBE-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 11 (DBE+) and 12 (DBE-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O4-1 (LBE+) - O4-3 (LBE-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O4-1 (LBE+) - O4-3 (LBE-) | Always | 1 MΩ or higher |
| O4-1(LBE+) - Body ground | Always | 1 MΩ or higher |
| O4-3 (LBE-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT INNER BELT LH |
![]() |
Connect the connector to the center airbag sensor and the front seat inner belt LH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 5.REPLACE FRONT SEAT INNER BELT LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the front seat inner belt LH (Click here).
| NEXT | |
| 6.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| OK | A |
| NG (w/ Cool Box) | B |
| NG (w/o Cool Box) | C |
|
| ||||
|
| ||||
| A | ||
| ||