Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1715    Front Acceleration Sensor RH Malfunction

DTC    C1716    Front Acceleration Sensor LH Malfunction

DTC    C1717    Rear Acceleration Sensor Malfunction

DTC    C1796    Front Acceleration Sensor RH Malfunction (Test Mode DTC)

DTC    C1797    Front Acceleration Sensor LH Malfunction (Test Mode DTC)

DTC    C1798    Rear Acceleration Sensor Malfunction (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The acceleration sensor (up and down G sensor) detects the upward and downward acceleration of the vehicle, and outputs it as a voltage to the suspension control ECU. Up and down G sensors are installed in 3 locations: 1) the suspension control ECU, 2) the driver side instrument panel, and 3) the passenger side instrument panel. Each up and down G sensor independently detects the upward and downward acceleration. During a test mode inspection, the suspension control ECU reads the fluctuations in each sensor's signal. If a sensor's signal does not fluctuate, test mode DTCs C1796, C1797 and C1798 are output.

DTC Code
Detection Condition
Trouble Area
C1715
With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at front acceleration sensor RH is detected for 1 second.
  1. Wire harness or connector
  2. Front acceleration sensor RH
  3. Suspension control ECU
C1716
With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at front acceleration sensor LH is detected for 1 second.
  1. Wire harness or connector
  2. Front acceleration sensor LH
  3. Suspension control ECU
C1717
With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear acceleration sensor is detected for 1 second.
  1. Suspension control ECU
C1796
On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
  1. Wire harness or connector
  2. Front acceleration sensor RH
  3. Suspension control ECU
C1797
On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
  1. Wire harness or connector
  2. Front acceleration sensor LH
  3. Suspension control ECU
C1798
On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
  1. Suspension control ECU

HINT:
If DTCs C1717 and C1798 (Rear Acceleration Sensor Malfunction) are output, replace the suspension control ECU (houses rear acceleration sensor).


WIRING DIAGRAM


C179515E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (G SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Data List.

    Air Suspension 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    (Up & Down) G Sensor FR
    G (up & down) front acceleration sensor RH reading /
    min.: -1045.29 m/s2
    max.: 1045.26 m/s2
    0 +/- 0.98 m/s2 at still condition
    Reading changes when vehicle (FR) is bounced
    (Up & Down) G Sensor FL
    G (up & down) front acceleration sensor LH reading /
    min.: -1045.29 m/s2
    max.: 1045.26 m/s2
    0 +/- 0.98 m/s2 at still condition
    Reading changes when vehicle (FL) is bounced
    (Up & Down) G Sensor Rear
    G (up & down) rear acceleration sensor reading /
    min.: -1045.29 m/s2
    max.: 1045.26 m/s2
    0 +/- 0.98 m/s2 at still condition
    Reading changes when vehicle (rear) is bounced

    OK:
    Acceleration value changes.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.INSPECT ACCELERATION SENSOR (FRONT LH OR RH)
  1. Turn the ignition switch off.



    C179517E01
  1. Check the acceleration sensor RH: (C1715, C1796).

    1. Remove the acceleration sensor RH (Click here).

    2. Connect 3 dry cell batteries of 1.5 V in series.

    3. Connect the positive (+) end of the batteries to terminal 3 (SHB) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SHG). Then measure the voltage between terminal 1 (SGFL) and terminal 2 (SHG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Sensor Condition
      Specified Condition
      1 (SGFL) - 2 (SHG)
      Sensor stationary
      Approx. 2.0 to 2.5 V
      Sensor is tilted
      Changes between approx. 0.9 to 2.3 V



    C179517E02
  1. Check the acceleration sensor LH: (C1716, C1797).

    1. Remove the acceleration sensor LH (Click here).

    2. Connect 3 dry cell batteries of 1.5 V in series.

    3. Connect the positive (+) end of the batteries to terminal 3 (SGV) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SGND). Then measure the voltage between terminal 1 (SGRR) and terminal 2 (SGND).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Sensor Condition
      Specified Condition
      1 (SGRR) - 2 (SGND)
      Sensor stationary
      Approx. 2.0 to 2.5 V
      Sensor is tilted
      Changes between approx. 0.9 to 2.3 V

      NOTICE:
      Do not apply a voltage of more than 6 V.

      HINT:
      When the acceleration sensor is tilted, it may output a different value.

      Result 
      Result
      Proceed to
      OK
      A
      NG (Front acceleration sensor RH)
      B
      NG (Front acceleration sensor LH)
      C



B
REPLACE FRONT ACCELERATION SENSOR RH (Click here)

C
REPLACE FRONT ACCELERATION SENSOR LH (Click here)
A


3.CHECK HARNESS AND CONNECTOR (FRONT ACCELERATION SENSOR - ECU AND BODY GROUND)


    C179518E01
  1. Check the acceleration sensor RH: (C1715, C1796).

    1. Disconnect the O17 and O18 ECU connector.

    2. Disconnect the H74 sensor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H74-1 (SGFL) - O18-27 (SGFR)
      Always
      Below 1 Ω
      H74-2 (SHG) - O17-22 (SGR)
      Always
      Below 1 Ω
      H74-3 (SHB) - O17-18 (SBR)
      Always
      Below 1 Ω
      H74-1 (SGFL) or O18-27 (SGFR) - Body ground
      Always
      10 kΩ or higher
      H74-2 (SHG) or O17-22 (SGR) - Body ground
      Always
      10 kΩ or higher
      H74-3 (SHB) or O17-18 (SBR) - Body ground
      Always
      10 kΩ or higher



    C179518E02
  1. Check the acceleration sensor LH: (C1716, C1797).

    1. Disconnect the O17 and O18 ECU connector.

    2. Disconnect the H75 sensor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H75-1 (SGRR) - O18-28 (SGRR)
      Always
      Below 1 Ω
      H75-2 (SGND) - O18-25 (SGR3)
      Always
      Below 1 Ω
      H75-3 (SGV) - O17-21 (SBR3)
      Always
      Below 1 Ω
      H75-1 (SGRR) or O18-28 (SGRR) - Body ground
      Always
      10 kΩ or higher
      H75-2 (SGND) or O18-25 (SGR3) - Body ground
      Always
      10 kΩ or higher
      H75-3 (SGV) or O17-21 (SBR3) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)