Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1731    Front Damping Force Control Actuator RH Circuit Malfunction

DTC    C1732    Front Damping Force Control Actuator LH Circuit Malfunction

DTC    C1733    Rear Damping Force Control Actuator RH Circuit Malfunction

DTC    C1734    Rear Damping Force Control Actuator LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The absorber control actuator switches the damping force depending on the suspension control ECU signals.

DTC Code
Detection Condition
Trouble Area
C1731
When either of the following is detected:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Wire harness or connector
  2. Front absorber control actuator RH
  3. Suspension control ECU
C1732
When either of the following is detected:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Wire harness or connector
  2. Front absorber control actuator LH
  3. Suspension control ECU
C1733
When either of the following is detected:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Wire harness or connector
  2. Rear absorber control actuator RH
  3. Suspension control ECU
C1734
When either of the following is detected:
  1. An actuator open-circuit signal is detected for at least 1 second when the actuator operates.
  2. An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.
  1. Wire harness or connector
  2. Rear absorber control actuator LH
  3. Suspension control ECU

WIRING DIAGRAM


C179519E03


INSPECTION PROCEDURE

NOTICE:
After replacing the suspension control ECU, perform registration (Click here).

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR GATE SOLENOID)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Damper Step FR
    Damper step (Front RH) /
    min.: 0 step
    max.: 255 steps
    min.: 1 step
    max.: 16 steps
    -
    Damper Step FL
    Damper step (Front LH) /
    min.: 0 step
    max.: 255 steps
    min.: 1 step
    max.: 16 steps
    -
    Damper Step RR
    Damper step (Rear RH) /
    min.: 0 step
    max.: 255 steps
    min.: 1 step
    max.: 16 steps
    -
    Damper Step RL
    Damper step (Rear LH) /
    min.: 0 step
    max.: 255 steps
    min.: 1 step
    max.: 16 steps
    -

    OK:
    The absorber control actuator operates.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.INSPECT ABSORBER CONTROL ACTUATOR
  1. Turn the ignition switch off.



    C179520E01
  1. Check the front absorber control actuator RH: (C1731).

    1. Disconnect the A44 actuator connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Sensor Condition
      Specified Condition
      1 (FAR+) - 2 (FAR-)
      Always
      6.4 to 7.2 Ω
      3 (FBR+) - 4 (FBR-)
      Always
      6.4 to 7.2 Ω



    C179520E02
  1. Check the front absorber control actuator LH: (C1732).

    1. Disconnect the A45 actuator connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Sensor Condition
      Specified Condition
      1 (FAL+) - 2 (FAL-)
      Always
      6.4 to 7.2 Ω
      3 (FBL+) - 4 (FBL-)
      Always
      6.4 to 7.2 Ω



    C179521E01
  1. Check the rear absorber control actuator RH: (C1733).

    1. Disconnect the Q6 actuator connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Sensor Condition
      Specified Condition
      1 (RAR-) - 2 (RAR+)
      Always
      6.4 to 7.2 Ω
      3 (RBR-) - 4 (RBR+)
      Always
      6.4 to 7.2 Ω



    C179521E02
  1. Check the rear absorber control actuator LH: (C1734).

    1. Disconnect the Q2 actuator connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Sensor Condition
      Specified Condition
      1 (RAL-) - 2 (RAL+)
      Always
      6.4 to 7.2 Ω
      3 (RBL-) - 4 (RBL+)
      Always
      6.4 to 7.2 Ω

      Result 
      Result
      Proceed to
      OK
      A
      NG (Front absorber control actuator RH)
      B
      NG (Front absorber control actuator LH)
      C
      NG (Rear absorber control actuator RH)
      D
      NG (Rear absorber control actuator LH)
      E



B
REPLACE FRONT ABSORBER CONTROL ACTUATOR RH (Click here)

C
REPLACE FRONT ABSORBER CONTROL ACTUATOR LH (Click here)

D
REPLACE REAR SHOCK ABSORBER ASSEMBLY RH (Click here)

E
REPLACE REAR SHOCK ABSORBER ASSEMBLY LH (Click here)
A


3.CHECK HARNESS AND CONNECTOR (ABSORBER CONTROL ACTUATOR - ECU AND BODY GROUND)


    C241564E02
  1. Check the front side absorber control actuator.

    1. Connect the A44 or A45 front absorber control actuator connector.

    2. Disconnect the O17 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for Front RH: (C1731) 
      Tester Connection
      Condition
      Specified Condition
      A44-1 (FAR+) - O17-7 (FAR+)
      Always
      Below 1 Ω
      A44-2 (FAR-) - O17-8 (FAR-)
      Always
      Below 1 Ω
      A44-3 (FBR+) - O17-1 (FBR+)
      Always
      Below 1 Ω
      A44-4 (FBR-) - O17-2 (FBR-)
      Always
      Below 1 Ω
      A44-1 (FAR+) or O17-7 (FAR+) - Body ground
      Always
      10 kΩ or higher
      A44-2 (FAR-) or O17-8 (FAR-) - Body ground
      Always
      10 kΩ or higher
      A44-3 (FBR+) or O17-1 (FBR+) - Body ground
      Always
      10 kΩ or higher
      A44-4 (FBR-) or O17-2 (FBR-) - Body ground
      Always
      10 kΩ or higher
      for Front LH: (C1732) 
      Tester Connection
      Condition
      Specified Condition
      A45-1 (FAL+) - O17-3 (FAL+)
      Always
      Below 1 Ω
      A45-2 (FAL-) - O17-5 (FAL-)
      Always
      Below 1 Ω
      A45-3 (FBL+) - O17-6 (FBL+)
      Always
      Below 1 Ω
      A45-4 (FBL-) - O17-4 (FBL-)
      Always
      Below 1 Ω
      A45-1 (FAL+) or O17-3 (FAL+) - Body ground
      Always
      10 kΩ or higher
      A45-2 (FAL-) or O17-5 (FAL-) - Body ground
      Always
      10 kΩ or higher
      A45-3 (FBL+) or O17-6 (FBL+) - Body ground
      Always
      10 kΩ or higher
      A45-4 (FBL-) or O17-4 (FBL-) - Body ground
      Always
      10 kΩ or higher



    C241565E02
  1. Check the rear side absorber control actuator.

    1. Connect the Q2 or Q6 rear absorber control actuator connector.

    2. Disconnect the O18 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for Rear RH: (C1733) 
      Tester Connection
      Condition
      Specified Condition
      Q6-1 (RAR-) - O18-2 (RAR-)
      Always
      Below 1 Ω
      Q6-2 (RAR+) - O18-1 (RAR+)
      Always
      Below 1 Ω
      Q6-3 (RBR-) - O18-4 (RBR-)
      Always
      Below 1 Ω
      Q6-4 (RBR+) - O18-3 (RBR+)
      Always
      Below 1 Ω
      Q6-1 (RAR-) or O18-2 (RAR-) - Body ground
      Always
      10 kΩ or higher
      Q6-2 (RAR+) or O18-1 (RAR+) - Body ground
      Always
      10 kΩ or higher
      Q6-3 (RBR-) or O18-4 (RBR-) - Body ground
      Always
      10 kΩ or higher
      Q6-4 (RBR+) or O18-3 (RBR+) - Body ground
      Always
      10 kΩ or higher
      for Rear LH: (C1734) 
      Tester Connection
      Condition
      Specified Condition
      Q2-1 (RAL-) - O18-6 (RAL-)
      Always
      Below 1 Ω
      Q2-2 (RAL+) - O18-5 (RAL+)
      Always
      Below 1 Ω
      Q2-3 (RBL-) - O18-8 (RBL-)
      Always
      Below 1 Ω
      Q2-4 (RBL+) - O18-7 (RBL+)
      Always
      Below 1 Ω
      Q2-1 (RAL-) or O18-6 (RAL-) - Body ground
      Always
      10 kΩ or higher
      Q2-2 (RAL+) or O18-5 (RAL+) - Body ground
      Always
      10 kΩ or higher
      Q2-3 (RBL-) or O18-8 (RBL-) - Body ground
      Always
      10 kΩ or higher
      Q2-4 (RBL+) or O18-7 (RBL+) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)