Home › Engine / Hybrid System › 3UR-FE LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



3. REMOVE RADIATOR ASSEMBLY
  1. Remove the radiator (Click here).



4. REMOVE AIR CLEANER ASSEMBLY


    A183242
  1. Loosen the hose clamp and disconnect the air cleaner from the air cleaner hose.

  1. Loosen the 2 bolts and remove the air cleaner with the grommet.



5. REMOVE AIR CLEANER HOSE ASSEMBLY


    A183244
  1. Disconnect the No. 2 ventilation hose.

  1. Disconnect the vacuum hose.

  1. Loosen the hose clamp and remove the air cleaner hose.



6. DISCONNECT INLET HEATER WATER HOSE C


    A183230
  1. Disconnect the inlet heater water hose from the No. 1 water by-pass pipe.



7. DISCONNECT OUTLET HEATER WATER HOSE C


    A183228
  1. Disconnect the outlet heater water hose from the water by-pass pipe.



8. SEPARATE ENGINE WIRE


9. SEPARATE NO. 2 ENGINE WIRE


10. REMOVE INTAKE MANIFOLD
  1. Remove the intake manifold (Click here).



11. DISCONNECT NO. 3 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)


    A183217
  1. Disconnect the No. 3 air injection hose.



12. DISCONNECT NO. 2 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)


    A183219
  1. Disconnect the connector and separate the wire harness clamp.

  1. Disconnect the No. 2 air injection hose.



13. SEPARATE COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



14. SEPARATE NO. 2 FUEL TUBE SUB-ASSEMBLY


    A165142E01
  1. Remove the 2 bolts and separate the fuel tube.



15. REMOVE OIL FILTER ELEMENT
  1. Remove the oil filter element (Click here).



16. REMOVE ENGINE OIL COOLER
  1. Remove the engine oil cooler (Click here).



17. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.

  1. Disconnect the wire harness clamp.



    A164432
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



18. REMOVE GENERATOR ASSEMBLY
  1. Remove the generator assembly (Click here).



19. REMOVE NO. 1 WATER BY-PASS HOSE


    A162549
  1. Remove the No. 1 water by-pass hose by disconnect the hose from the water inlet housing and front water by-pass joint.



20. SEPARATE AIR PIPE SUB-ASSEMBLY (w/ Secondary Air Injection System)


    A183221
  1. Disconnect the connector and separate the 2 clamps and wire harness.

  1. Remove bolt and separate the air pipe.



21. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A162551
  1. Disconnect the 2 hoses.

  1. Remove the 2 bolts and water by-pass pipe.



22. SEPARATE NO. 1 WATER BY-PASS PIPE
  1. Remove the 2 bolts and separate the No. 1 water by-pass pipe.



23. REMOVE FRONT WATER BY-PASS JOINT


    A162552
  1. Disconnect the No. 2 water by-pass hose from the water by-pass joint.

  1. Remove the 4 nuts, water by-pass joint and 2 gaskets.



24. REMOVE NO. 2 CYLINDER HEAD COVER


A158576
  1. Remove the No. 2 cylinder head cover.



25. REMOVE NO. 1 ENGINE COVER


A158581
  1. Remove the No. 1 engine cover.



26. REMOVE AIR PIPE SUB-ASSEMBLY (w/ Secondary Air Injection System)


    A162553
  1. Remove the bolt, disconnect the 2 hoses, and remove the air pipe.



27. REMOVE INLET WATER HOUSING


    A183226
  1. Remove the 3 bolts and inlet water housing and disconnect the No. 3 water by-pass hose from the inlet water housing.

  1. Remove the gasket from the water pump.



28. REMOVE WATER PUMP PULLEY


    A151837E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.



29. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A162557
  1. Remove the bolt and idler pulley.



30. REMOVE FLUID COUPLING BRACKET


    A162558
  1. Remove the 4 bolts and fluid coupling bracket.



31. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A162527
  1. Remove the standard bolt, 6 mm hexagon wrench bolt and belt tensioner.



32. REMOVE IGNITION COIL ASSEMBLY


    A151832
  1. Disconnect the 8 ignition coil connectors.

  1. Remove the 8 bolts and 8 ignition coils.



33. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A162523
  1. Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure that the removed parts are returned to the same places they were removed from.



    A162524
  1. Remove the 5 O-rings from the camshaft bearing caps (No. 2, No. 3).



34. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A162525
  1. Remove the 14 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure that the removed parts are returned to the same places they were removed from.



    A162526
  1. Remove the 5 O-rings from the camshaft bearing caps (No. 1, No. 3).



35. REMOVE CRANKSHAFT PULLEY


    A164228E01
  1. Using SST, loosen the crankshaft pulley set bolt.

    SST
    09213-70011  
    09330-00021  

  1. Partially install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.



    A164229E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



36. DISCONNECT WIRE HARNESS CLAMP BRACKET


    A163733
  1. Remove the bolt and disconnect the bracket.



37. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


    A162529E01
  1. Remove the 28 bolts and nut shown in the illustration.



    A162530
  1. Remove the timing chain cover by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the cylinder head and cylinder block contact surfaces of the chain cover.



    A162531
  1. Remove the oil pump gasket from the cylinder block.



    A164415
  1. Remove the O-ring from the oil pan.



38. REMOVE INLET WATER PIPE


    A162532
  1. Remove the inlet water pipe.

  1. Remove the 2 O-rings from the inlet water pipe.