Home › Engine / Hybrid System › 3UR-FE LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



3. REMOVE RADIATOR ASSEMBLY
(Click here).


4. REMOVE AIR CLEANER ASSEMBLY


    A183242
  1. Loosen the hose clamp and disconnect the air cleaner from the air cleaner hose.

  1. Loosen the 2 bolts and remove the air cleaner with the grommet.



5. REMOVE AIR CLEANER HOSE ASSEMBLY


    A183244
  1. Disconnect the No. 2 ventilation hose.

  1. Disconnect the vacuum hose.

  1. Loosen the hose clamp and remove the air cleaner hose.



6. DISCONNECT INLET HEATER WATER HOSE C


    A183230
  1. Slide the clamp and disconnect the inlet heater water hose C from the water by-pass pipe sub-assembly.



7. DISCONNECT OUTLET HEATER WATER HOSE C


    A183228
  1. Slide the clamp and disconnect the outlet heater water hose C from the No. 1 water by-pass pipe.



8. SEPARATE ENGINE WIRE


9. SEPARATE NO. 2 ENGINE WIRE


10. REMOVE INTAKE MANIFOLD
(Click here).


11. SEPARATE COOLER COMPRESSOR ASSEMBLY


    A163332
  1. Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

    HINT:
    It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



12. SEPARATE NO. 2 FUEL TUBE SUB-ASSEMBLY


    A165142E05
  1. Remove the 2 bolts and separate the No. 2 fuel tube sub-assembly.
    Text in Illustration 
    *a
    LH Side
    *b
    RH Side



13. REMOVE OIL FILTER ELEMENT
(Click here).


14. REMOVE ENGINE OIL COOLER
(Click here).


15. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick from the engine oil level dipstick guide.

  1. Disconnect the wire harness clamp.



    A164432
  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



16. REMOVE GENERATOR ASSEMBLY
(Click here).


17. REMOVE NO. 1 WATER BY-PASS HOSE


    A308519
  1. Slide the 2 clamps and remove the No. 1 water by-pass hose from the inlet water housing and front water by-pass joint.



18. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A162551
  1. Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.

  1. Remove the 2 bolts and water by-pass pipe sub-assembly.



19. SEPARATE NO. 1 WATER BY-PASS PIPE
  1. Remove the 2 bolts and separate the No. 1 water by-pass pipe.



20. DISCONNECT NO. 9 WATER BY-PASS HOSE


    A291559E02
  1. Slide the clamp and disconnect the No. 9 water by-pass hose from the front water by-pass joint.
    Text in Illustration 
    *1
    No. 9 Water By-pass Hose
    *2
    No. 10 Water By-pass Hose



21. DISCONNECT NO. 10 WATER BY-PASS HOSE
  1. Slide the clamp and disconnect the No. 10 water by-pass hose from the front water by-pass joint.



22. REMOVE FRONT WATER BY-PASS JOINT


    A291566
  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.

  1. Remove the 4 nuts, front water by-pass joint and 2 gaskets.



23. REMOVE NO. 3 WATER BY-PASS PIPE


A307664

HINT:
Perform this procedure only when replacement of the No. 3 water by-pass pipe is necessary.

  1. Remove the bolt and No. 3 water by-pass pipe.



24. REMOVE NO. 2 CYLINDER HEAD COVER


A158576
  1. Remove the No. 2 cylinder head cover.



25. REMOVE NO. 1 ENGINE COVER


A158581
  1. Remove the No. 1 engine cover.



26. REMOVE INLET WATER HOUSING


    A183226
  1. Remove the 3 bolts and inlet water housing and disconnect the No. 3 water by-pass hose from the inlet water housing.

  1. Remove the gasket from the water pump.



27. REMOVE WATER PUMP PULLEY


    A151837E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.



28. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A162557
  1. Remove the bolt and No. 1 idler pulley sub-assembly.



29. REMOVE FLUID COUPLING BRACKET


    A162558
  1. Remove the 4 bolts and fluid coupling bracket.



30. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A162527
  1. Remove the standard bolt, 6 mm hexagon wrench bolt and V-ribbed belt tensioner assembly.



31. REMOVE IGNITION COIL ASSEMBLY


    A151832
  1. Disconnect the 8 ignition coil connectors.

  1. Remove the 8 bolts and 8 ignition coils.



32. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A162523
  1. Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.

    HINT:
    Make sure that the removed parts are returned to the same places they were removed from.



    A162524
  1. Remove the 5 O-rings from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.



33. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A162525
  1. Remove the 14 bolts, seal washer, cylinder head cover sub-assembly and gasket.

    HINT:
    Make sure that the removed parts are returned to the same places they were removed from.



    A162526
  1. Remove the 5 O-rings from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.



34. REMOVE CRANKSHAFT PULLEY


    A164228E01
  1. Using SST, loosen the crankshaft pulley set bolt.

    SST
    09213-70011  
    09330-00021  

  1. Partially install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.



    A164229E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



35. DISCONNECT WIRE HARNESS CLAMP BRACKET


    A163733
  1. Remove the bolt and disconnect the wire harness clamp bracket.



36. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


    A162529E02
  1. Remove the 28 bolts and nut shown in the illustration.
    Text in Illustration 
    *1
    Nut



    A162530
  1. Remove the timing chain or belt cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the cylinder head and cylinder block contact surfaces of the timing chain or belt cover sub-assembly.



    A162531
  1. Remove the oil pump gasket from the cylinder block.



    A164415
  1. Remove the O-ring from the oil pan sub-assembly.



37. REMOVE INLET WATER PIPE


    A162532
  1. Remove the inlet water pipe from the No. 1 heat exchanger cover.

  1. Remove the 2 O-rings from the inlet water pipe.