Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY (w/o Cool Box)

CENTER AIRBAG SENSOR ASSEMBLY (w/o Cool Box) > INSTALLATION

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. INSTALL AIRBAG SENSOR ASSEMBLY


B192369
  1. Check that the ignition switch is turned off.

  1. Check that the negative battery terminal is disconnected.

    CAUTION:
    1. Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.
    2. Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Install the airbag sensor with the 3 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Do not use an airbag sensor that has been dropped.
    2. Do not subject the airbag sensor to any impact or force.
    3. Confirm that the carpet does not interfere with the installation plane.

  1. Confirm that there is no looseness by shaking the front airbag sensor.



    B192368E01
  1. Connect the connector holder to lock the lever.

    NOTICE:
    Confirm that the lever is locked.

  1. Confirm that the drip-proof sheet has not been removed and does not cut into the connectors.



2. INSTALL FRONT CONSOLE BOX


B222975
  1. Install the front console box with the 5 screws and 2 clips.

  1. Attach the 2 clamps.



3. INSTALL REAR CONSOLE BOX ASSEMBLY


B192330
  1. Attach the 6 claws to install the rear console box.

  1. Install the 2 screws and 4 bolts.



    B188223
  1. Connect the connectors.



4. INSTALL CONSOLE BOX CARPET


B188222
  1. Install the console box carpet.



5. INSTALL REAR CONSOLE BOX POCKET


B188221
  1. Install the rear console box pocket.



6. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


    B222976
  1. Connect the connectors.

  1. Attach the 6 clips to install the console panel.

  1. Install the clip.



7. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B161742
  1. Attach the 12 clips to install the console panel.



8. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B167312
  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


    B163883
  1. Attach the 2 claws to install the sensor.



    B229064
  1. Connect the connectors.

  1. Attach the 9 clips and claw to install the finish panel.

  1. Install the 2 <A> bolts.



10. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.

  1. Attach the 3 claws to install the hood lock lever



11. INSTALL INSTRUMENT SIDE PANEL LH


    B229058
  1. Attach the 7 claws to install the side panel.



12. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



13. INSTALL FRONT PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



14. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



15. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



17. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).