INSTRUMENT PANEL SAFETY PAD > INSTALLATION |
| 1. INSTALL NO. 1 INSTRUMENT PANEL PIN |
![]() |
Install the 2 instrument panel pins with the 2 <G> screws.
| 2. INSTALL AUTOMATIC LIGHT CONTROL SENSOR |
![]() |
Attach the 2 claws to install the automatic light control sensor.
| 3. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY |
![]() |
Connect the airbag connector to install the instrument panel wire.
![]() |
Attach the 10 hooks and install the front passenger airbag on the instrument panel.
Attach the 2 clamps.
Install the 2 screws.
| 4. INSTALL NO. 2 INSTRUMENT PANEL WIRE |
Attach the clamps to install the instrument panel wire.
Connect the 2 connectors.

| 5. INSTALL ACCESSORY METER ASSEMBLY |
![]() |
Install the accessory meter with the 3 screws.
| 6. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Install the register with the 3 <G> screws.
| 7. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY |
![]() |
Install the register with the 3 <G> screws.
| 8. INSTALL DEFROSTER NOZZLE ASSEMBLY |
![]() |
Install the defroster nozzle with the 3 <G> screws.
| 9. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Attach the 2 claws to install the duct.
Install the 2 <G> screws.
| 10. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Attach the 2 claws to install the duct.
Install the 2 <G> screws.
| 11. INSTALL NO. 1 HEATER TO REGISTER DUCT |
Install the duct with the 5 <G> screws.
Attach the clamp.

| 12. INSTALL NO. 1 INSTRUMENT PANEL CLIP |
Attach the 2 claws to install the 2 clips.

| 13. INSTALL NO. 3 INSTRUMENT PANEL STAY |
Attach the 3 claws to install the 3 stays.

| 14. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers) |
Attach the 5 clips to install the instrument panel.

Install the 3 <C> bolts and 2 <E> nuts.
Install the 2 <F> passenger airbag bolts.

Connect the connectors and attach the clamps.
Install the wire harness with the bolt.

![]() |
Connect the airbag connector.
| 15. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers) |
Attach the 5 clips to install the instrument panel.

Install the 3 <C> bolts and 2 <E> nuts.
Install the 2 <F> passenger airbag bolts.

Connect the connectors and attach the clamps.
Install the wire harness with the bolt.

![]() |
Connect the airbag connector.
| 16. INSTALL REAR NO. 4 AIR DUCT (for 14 Speakers) |
![]() |
Attach the 4 claws to install the air duct.
Install the clip.
| 17. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers) |
![]() |
Install the amplifier with the 3 bolts.
Connect the 4 connectors.
| 18. INSTALL AUDIO AMPLIFIER COVER (for 14 Speakers) |
![]() |
Set the cover on the stereo amplifier assembly.
Attach the 3 clips.
| 19. INSTALL FRONT SEAT ASSEMBLY RH (for 14 Speakers) |
Place the front seat assembly in the cabin.
Connect the seat wire connectors under the seat.
Connect the cable to the negative (-) battery terminal.
![]() |
Operate the leg support adjustment switch to move the seat cushion to the closed position.
Operate the power seat switch (slide switch) to move the seat to the rearmost position.
![]() |
Install the 2 bolts.
Operate the power seat switch (slide switch) to move the seat to the foremost position.
![]() |
Install the 2 bolts.
| 20. INSTALL SEAT TRACK OUTER COVER RH (for 14 Speakers) |
![]() |
Attach the 2 claws to install the seat track cover.
| 21. INSTALL SEAT TRACK INNER COVER RH (for 14 Speakers) |
![]() |
Attach the 2 claws to install the seat track cover.
| 22. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH (w/ Cover) |
Operate the power seat switch (slide switch) to move the seat to the rearmost position.
![]() |
Attach the 4 claws in the order shown in the illustration to install the cover.
| 23. INSTALL FRONT INNER SEAT TRACK BRACKET COVER (w/ Cover) |
![]() |
Attach the 4 claws in the order shown in the illustration to install the cover.
| 24. INSTALL FRONT SEAT HEADREST ASSEMBLY (for 14 Speakers) |
| 25. INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers) |
![]() |
Connect the connector.
Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.
Install the speaker with the 2 bolts.
| 26. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Attach the 6 clips and 2 claws to install the speaker panel.
| 27. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH |
![]() |
Connect the speaker connector.
Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.
Install the speaker with the 2 bolts.
| 28. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Attach the 4 clips and claw to install the speaker panel.
| 29. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH |
![]() |
Connect the speaker connector.
Temporarily install the speaker by aligning the positioning pins of the speaker with the instrument panel.
Install the speaker with the 2 bolts.
| 30. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY |
![]() |
Attach the 4 clips and claw to install the speaker panel.
| 31. INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY |
![]() |
Attach the clip to install the box door.
Install the 6 <B> screws.
| 32. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH |
![]() |
Connect the connector.
![]() |
Attach the 3 claws to install the finish panel.
Install the 3 <D> screws and bolt <A>.
| 33. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Connect the connector.
Install the 3 bolts to install the instrument panel airbag.
| 34. INSTALL LOWER INSTRUMENT PANEL |
![]() |
Attach the 2 claws to install the panel.
Install the bolt and screw.
| 35. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Attach the 2 guides and 4 claws.
Attach the clip to install the under cover.
| 36. INSTALL FRONT PILLAR GARNISH RH |
![]() |
Remove the protective cover.
Attach the claw to install the front pillar garnish.
Install the assist grip with the 2 bolts.
Attach the 2 claws to install the 2 assist grip plugs.

| 37. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | White |
| LH side | Yellow |
| 38. INSTALL COWL SIDE TRIM BOARD RH |
![]() |
Attach the 2 clips to install the cowl side trim board.
Install the clip.
| 39. INSTALL FRONT DOOR SCUFF PLATE RH |
![]() |
Attach the 9 claws to install the scuff plate.
| 40. INSTALL INSTRUMENT SIDE PANEL RH |
![]() |
Attach the 6 claws to install the side panel.
| 41. INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL WITH BRACKET (w/o Radio Receiver) |
![]() |
Attach the 3 clips to install the upper instrument cluster finish panel with bracket.
![]() |
Install the 4 bolts.
| 42. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver) |
![]() |
Connect the connectors.
Insert the radio receiver and attach the 3 clips on its backside.
![]() |
Install the radio receiver with the 4 bolts.
| 43. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY |
![]() |
Connect the connectors.
Attach the 4 clips and install the panel.
| 44. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL |
![]() |
Connect the connectors.
Attach the 4 clips and 2 claws to install the finish panel.
| 45. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Connect the connector and engage the clip and install the combination meter assembly.
![]() |
Install the 4 screws.
| 46. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY |
![]() |
Attach the 12 clips to install the finish panel.
Connect the 2 connectors and clamp.
![]() |
Attach the 4 claws to install the instrument panel finish panel retainer.
| 47. INSTALL FRONT CONSOLE BOX |
![]() |
Install the front console box with the 5 screws and 2 clips.
Attach the 2 clamps.
| 48. INSTALL REAR CONSOLE BOX ASSEMBLY |
![]() |
Attach the 6 claws to install the rear console box.
Install the 2 screws and 4 bolts.
![]() |
Connect the connectors.
| 49. INSTALL CONSOLE BOX CARPET |
![]() |
Install the console box carpet.
| 50. INSTALL REAR CONSOLE BOX POCKET |
![]() |
Install the rear console box pocket.
| 51. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Connect the connectors.
Attach the 6 clips to install the console panel.
Install the clip.
| 52. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Attach the 12 clips to install the console panel.
| 53. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
![]() |
Install the shift lever knob and twist it in the direction indicated by the arrow.
| 54. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Connect the connector.
Attach the 2 claws to install the DLC3.
Install the 4 bolts to install the instrument panel airbag.
| 55. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
![]() |
Attach the 2 claws to install the sensor.
![]() |
Connect the connectors.
Attach the 9 clips and claw to install the finish panel.
Install the 2 <A> bolts.
| 56. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.
Attach the 3 claws to install the hood lock lever
| 57. INSTALL INSTRUMENT SIDE PANEL LH |
![]() |
Attach the 7 claws to install the side panel.
| 58. INSTALL FRONT PILLAR GARNISH LH |
| 59. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 60. INSTALL COWL SIDE TRIM BOARD LH |
| 61. INSTALL FRONT DOOR SCUFF PLATE LH |
| 62. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Install the turn signal switch with spiral cable to the steering column with the clamp.
![]() |
Connect the 6 connectors to the turn signal switch with spiral cable.
| 63. INSTALL UPPER STEERING COLUMN COVER |
![]() |
Attach the claw to install the upper steering column cover.
Attach the 4 clips.
| 64. INSTALL LOWER STEERING COLUMN COVER |
![]() |
Attach the 2 claws to install the lower steering column cover.
Install the 2 screws.
| 65. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel and steering main shaft.
Install the steering wheel set nut.
| 66. INSTALL STEERING PAD |
![]() |
Check that the ignition switch is turned off.
Check that the negative battery terminal is disconnected.
Connect the horn connector.
Connect the airbag connector.
Install the steering pad.
![]() |
Using T30 "TORX" socked wrench, tighten the 2 screws.
| 67. INSTALL LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Attach the 2 claws to install the cover.
| 68. INSTALL LOWER NO. 2 STEERING WHEEL COVER |
![]() |
Attach the 2 claws to install the cover.
| 69. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 70. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).