Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT

FRONT AIR CONDITIONING UNIT > INSTALLATION

for Preparation Click here



1. INSTALL ECU COVER
  1. Install the ECU cover with the 2 screws.



2. INSTALL FRONT AIR CONDITIONING UNIT


I104401
  1. Temporarily tighten the air conditioning unit with the 3 bolts and 2 screws.



3. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Connect the connector and clamp and install the wire harness.



  1. Install the instrument panel reinforcement.

    1. for Passenger Side:
      Using a 12 mm hexagon wrench, install the 2 collars.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    2. for Passenger Side:
      Using a T40 "TORX" socket, install the 2 bolts.

      Torque:
      18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    3. for Driver Side:
      Install the 3 bolts and 2 caps.



    4. Install the instrument panel reinforcement with the 3 bolts and nut.

      1. for Nut

      Torque:
      5.4 N*m{ 55 kgf*cm , 48 in.*lbf } for nut



      I104455E02

      Text in Illustration 
      *1
      "TORX" Bolt
      *2
      Collar



    I104401
  1. Tighten the air conditioning unit with the 3 bolts and 2 screws.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf } for bolt

  1. Connect the connectors and clamps and install the wire harness.

  1. Install the ground wire with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



4. INSTALL AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Cool Box)
  1. Sufficiently apply compressor oil to 4 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 4 O-rings to the air conditioner tube and accessory.

  1. Install the air conditioner tube and accessory with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    E112921E01
  1. Connect the air conditioner tube and accessory with the 2 piping clamps.

    NOTICE:
    After connection, check the claw engagement of the 2 piping clamps.



5. INSTALL NO. 1 ECU INTEGRATION BRACKET
  1. Install the ECU integration bracket with the bolt and nut.

  1. Connect the connectors and clamp.



6. INSTALL TURN SIGNAL FLASHER ASSEMBLY
  1. Install the turn signal flasher with the nut.

  1. Connect the connector.



7. INSTALL MAIN BODY ECU
  1. Install the main body ECU with the bolt and nut.

  1. Connect the connectors and clamp.



8. INSTALL REAR NO. 2 AIR DUCT
  1. Attach the 3 claws to install the air duct.



9. INSTALL REAR NO. 1 AIR DUCT
  1. Attach the 3 claws to install the air duct.



10. INSTALL STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
(Click here)


11. INSTALL STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)
(Click here)


12. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


13. INSTALL REAR NO. 4 AIR DUCT
  1. Attach the 4 claws to install the air duct.

  1. Install the clip.



14. INSTALL REAR NO. 3 AIR DUCT
  1. Attach the 4 claws to install the air duct.

  1. Install the clip.



15. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers)


    B190161
  1. Install the amplifier with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 4 connectors.



16. INSTALL AUDIO AMPLIFIER COVER (for 14 Speakers)


    B190162
  1. Set the cover on the stereo amplifier assembly.

  1. Attach the 3 clips.



17. INSTALL FRONT RH SEAT ASSEMBLY (for RH Side)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the seat wire connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



    B167189
  1. Operate the leg support adjustment switch to move the seat cushion to the closed position.

  1. Operate the power seat switch (slide switch) to move the seat to the rearmost position.



    B194824
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Operate the power seat switch (slide switch) to move the seat to the foremost position.



    B191041
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



18. INSTALL SEAT TRACK OUTER COVER RH (for RH Side)


    B200255
  1. Attach the 2 claws to install the seat track cover.



19. INSTALL SEAT TRACK INNER COVER RH (for RH Side)


    B232179E01
  1. Attach the 4 claws in the order shown in the illustration to install the cover.



20. INSTALL FRONT SEAT TRACK BRACKET COVER INNER RH (for RH Side)


    B232173E01
  1. Attach the 4 claws in the order shown in the illustration to install the cover.



21. INSTALL FRONT SEAT TRACK BRACKET COVER OUTER RH (for RH Side)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B232174E01
  1. Attach the 4 claws in the order shown in the illustration to install the cover.



22. INSTALL FRONT SEAT HEADREST ASSEMBLY (for RH Side)


23. INSTALL FRONT LH SEAT ASSEMBLY (for LH Side)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the seat wire connectors under the seat.

  1. Lift up the seat track adjusting handle to move the seat to the rearmost position.



    B191042
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Lift up the seat track adjusting handle to move the seat to the foremost position.



    B191041
  1. Install the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



24. INSTALL SEAT TRACK OUTER COVER LH (for LH Side)


    B200255
  1. Attach the 2 claws to install the seat track cover.



25. INSTALL SEAT TRACK INNER COVER LH (for LH Side)


    B191067
  1. Attach the 2 claws to install the seat track cover.



26. INSTALL FRONT SEAT TRACK BRACKET COVER INNER LH (for LH Side)


    B232173E01
  1. Attach the 4 claws in the order shown in the illustration to install the cover.



27. INSTALL FRONT SEAT TRACK BRACKET COVER OUTER LH (for LH Side)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B232174E01
  1. Attach the 4 claws in the order shown in the illustration to install the cover.



28. INSTALL FRONT SEAT HEADREST ASSEMBLY (for LH Side)


29. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


30. CONNECT HEATER WATER OUTLET HOSE A


E191226E02
  1. Connect the water hose onto the air conditioning unit.
    Text in Illustration 
    *a
    View A
    *b
    Upper Side
    *c
    Yellow Paint Mark

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle.



31. CONNECT HEATER WATER INLET HOSE A


E191227E02
  1. Connect the water hose onto the air conditioning unit.
    Text in Illustration 
    *a
    View A
    *b
    Upper Side
    *c
    White Paint Mark

    NOTICE:
    Perform the installation with the hose clip and mark at the correct angle.



32. CONNECT COOLER REFRIGERANT LIQUID PIPE B


I104457
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the suction pipe.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings on the suction pipe and liquid pipe.

  1. Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



33. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that it moves smoothly and correctly into position.

  1. Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.
    If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.



34. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to the N position.



    C155901E02
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E02
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



36. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    14.6 liters (15.4 US qts., 12.8 Imp. qts.)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



37. INSPECT FOR COOLANT LEAK


A161766E01

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



38. CHARGE REFRIGERANT



I100449E02

NOTICE:
Charge refrigerant in accordance with the equipment manual.

  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    Standard:
    Cool Box
    Refrigerant Charging Amount
    w/ Cool Box
    1080 to 1140 g (38.1 to 40.2 oz.)
    w/o Cool Box
    920 to 980 g (32.4 to 34.6 oz.)

    NOTICE:
    Do not start the engine before charging it with refrigerant as the cooler compressor does not work properly without sufficient refrigerant. This could cause the compressor to overheat.

    HINT:

    1. The relationship between the refrigerant charge amount and the pressure is as follows.


      I103968E01

    2. High Charge Range:
      If the refrigerant is overcharged, the pressure rises on the high-pressure side. High-pressure cut off frequently occurs. This causes insufficient cooling performance and also insufficient compressor lubrication.
    3. Low Charge Range:
      A shortage of refrigerant causes insufficient cooling performance and low circulation of refrigerant oil, which shortens the compressor life. Operation with insufficient coolant raises the refrigerant temperature and causes heat deterioration of the rubber seals and hoses. Cracking and subsequent refrigerant leakage may occur.


    1. Install the caps onto the service valves on the refrigerant line.



39. WARM UP ENGINE

NOTICE:
Warm up the engine at less than 2000 rpm for 1 minute or more after charging it with refrigerant.



40. INSPECT FOR REFRIGERANT LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation as follows:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system.
      When the compressor is off: approximately 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

    HINT:
    It is impossible for the above pressure to be maintained if there is leakage.



    I042222E14
  1. Using the halogen leak detector, check the refrigerant line, especially at the connection points, for leakage.

  1. If no gas leakage is detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.



41. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    1. Bolt

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    1. Screw

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



42. CHECK SRS WARNING LIGHT
(Click here)