Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT

FRONT AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.



B192378E01



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



4. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.



    E181845E01
  1. Remove the caps from the service valves on the refrigerant line.

  1. Connect the refrigerant recovery unit.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.

    NOTICE:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  1. Tighten the radiator drain cock plug by hand.


    A151835E01



6. REMOVE COOLER REFRIGERANT LIQUID PIPE B


I104456
  1. Remove the bolt, and slide the hook connector.



    I043960E02
  1. Disconnect the suction pipe and liquid pipe.

    NOTICE:
    1. Do not use a screwdriver or similar tool to disconnect the pipe.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  1. Remove the 2 O-rings from the suction pipe and liquid pipe.



7. REMOVE HEATER WATER HOSE INLET A


E191224
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose.

    NOTICE:
    1. Do not apply excessive force to the rear heater outlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



8. REMOVE HEATER WATER OUTLET HOSE A


E191225
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose.

    NOTICE:
    1. Do not apply excessive force to the rear heater inlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E161312
  1. Remove the nut and remove the wiper arm and blade assembly.



10. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

HINT:
Use the same procedure for both sides.



11. REMOVE FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Detach the claw and remove the front fender to cowl side seal.



12. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



13. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161315
  1. Remove the 2 clips.

  1. Remove the 6 claws and 8 guides and remove the cowl top ventilator louver sub-assembly.



14. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY


    E161316
  1. Disconnect the connector.

  1. Remove the nut.

  1. Remove the 4 bolts and wiper motor and link assembly.



15. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. Using a screwdriver, detach the 2 claws and remove the steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



16. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Using a screwdriver, detach the 2 claws and remove the steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



17. REMOVE STEERING PAD


    C180934
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.

  1. Pull the steering pad toward you.



    B166581
  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the 2 connectors.

  1. Disconnect the horn connector.



18. REMOVE STEERING WHEEL ASSEMBLY


    C180956
  1. Detach the cruise control main wire harness clamp from the steering wheel side.

  1. Disconnect the steering pad switch connector and cruise control main switch connector from the spiral cable.

  1. Remove the steering wheel set nut.



    C180950E01
  1. Put matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



19. REMOVE LOWER STEERING COLUMN COVER


C181134
  1. Remove the 2 screws.

  1. Detach the 2 claws to remove the lower steering column cover.



20. REMOVE UPPER STEERING COLUMN COVER


    C159215
  1. Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.



21. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


C180951
  1. Disconnect the all connectors from the turn signal switch with spiral cable.



    C159216
  1. Using pliers, grip the claws of the clamp and remove the turn signal switch with spiral cable from the steering column.



22. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure for both sides.



23. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure for both sides.



24. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for both sides.



25. REMOVE FRONT PILLAR GARNISH LH

HINT:
Use the same procedure for both sides.



26. REMOVE INSTRUMENT SIDE PANEL LH


    B226739
  1. Using a moulding remover, detach the 7 claws and remove the side panel.



27. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B192511
  1. Detach the 3 claws.

  1. Disconnect the hood lock control cable and remove the hood lock control lever sub-assembly.



28. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


B229064
  1. Remove the 2 <A> bolts.

  1. Detach the 9 clips and claw.



    B163883
  1. Detach the 2 claws and remove the sensor.

  1. Remove the finish panel and then disconnect the connectors.



29. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225997
  1. Remove the 4 bolts and remove the instrument panel airbag.

  1. Detach the 2 claws and disconnect the DLC3.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



30. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B161741
  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



31. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


B161742
  1. Detach the 12 clips and remove the console panel.



32. REMOVE REAR CONSOLE BOX POCKET


B188221
  1. Remove the rear console box pocket.



33. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY


B222976
  1. Move the shift lever to N.

  1. Remove the clip.

  1. Detach the 6 clips and remove the console panel.

  1. Disconnect the connector



34. REMOVE CONSOLE BOX CARPET


B188222
  1. Remove the console box carpet.



35. REMOVE REAR CONSOLE BOX ASSEMBLY


B188223
  1. Disconnect the connectors.



    B192330
  1. Remove the 4 bolts and 2 screws.

  1. Detach the 6 claws and remove the rear console box.



36. REMOVE FRONT CONSOLE BOX


B222975
  1. Detach the 2 clamps.

  1. Remove the 2 clips.

  1. Remove the 5 screws and the front console box.



37. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


B192334
  1. Detach the 4 claws and remove the instrument panel finish panel retainer.



    B219715
  1. Disconnect the 2 connectors and wire harness clamp.

  1. Detach the 12 clips and remove the finish panel.



38. REMOVE COMBINATION METER ASSEMBLY


    E161309
  1. Remove the 4 screws.



    E141678
  1. Disconnect the connector and disengage the clip and remove the combination meter assembly.



39. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL


    B223270
  1. Detach the 4 clips and 2 claws.

  1. Disconnect the connectors and remove the finish panel.



40. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    I104352
  1. Detach the 4 clips and separate the panel.

  1. Disconnect the connectors and remove the panel.



41. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)


    B224307
  1. Remove the 4 bolts.



    B224308
  1. Pull the radio receiver to detach the 3 clips on the backside of the radio receiver.

  1. Disconnect the connectors and remove the radio receiver.



42. REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL WITH BRACKET (w/o Radio Receiver)


    B219551
  1. Remove the 4 bolts.



    B219552
  1. Detach the 3 clips and remove the upper instrument cluster finish panel with bracket.



43. REMOVE INSTRUMENT SIDE PANEL RH


    B229197
  1. Using a moulding remover, detach the 6 claws and remove the side panel.



44. REMOVE FRONT DOOR SCUFF PLATE RH


    B190151
  1. Detach the 9 claws and remove the scuff plate.



45. REMOVE COWL SIDE TRIM BOARD RH


    B190152
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



46. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B191803
  1. Remove the front door opening trim weatherstrip.



47. REMOVE FRONT PILLAR GARNISH RH
  1. Using a screwdriver with its tip wrapped in protective tape, detach the 2 claws and remove the 2 assist grip plugs.

  1. Remove the 2 bolts and assist grip.



  1. Detach the claw and remove the front pillar garnish.


    B190131E01



    B190132E01
  1. Protect the curtain shield airbag.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



48. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


B226758
  1. Detach the clip and 4 claws.

  1. Detach the 2 guides and remove the under cover.



49. REMOVE LOWER INSTRUMENT PANEL


    B226759
  1. Remove the screw and bolt.

  1. Detach the 2 claws and remove the panel.



50. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B226007
  1. Remove the 3 bolts and remove the instrument panel airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



51. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


B226741
  1. Remove the bolt <A> and 3 <D> screws.

  1. Detach the 3 claws and remove the finish panel.



    B230430
  1. Disconnect the connector.



52. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    B228240
  1. Remove the 6 <B> screws.

  1. Detach the clip and remove the box door.



53. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192345E01
  1. Using a moulding remover, detach the 4 clips and claw, and remove the speaker panel.



54. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH


    E161075
  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.

    NOTICE:
    Do not touch the cone part of the speaker.



55. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192349E01
  1. Using a moulding remover, detach the 4 clips and claw, and remove the speaker panel.



56. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH


    E161074
  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.

    NOTICE:
    Do not touch the cone part of the speaker.



57. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


B192347E01
  1. Using a moulding remover, detach the 6 clips and 2 claws, and remove the speaker panel.



58. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 14 Speakers)


    B165751E01
  1. Remove the 2 bolts.

  1. Remove the speaker and disconnect the connector.

    NOTICE:
    Do not touch the cone part of the speaker.



59. REMOVE FRONT SEAT HEADREST ASSEMBLY (for LH Side)


60. REMOVE FRONT SEAT TRACK BRACKET COVER INNER LH (for LH Side)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B232171E01
  1. Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



61. REMOVE FRONT SEAT TRACK BRACKET COVER OUTER LH (for LH Side)


    B232172E01
  1. Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



62. REMOVE SEAT TRACK INNER COVER LH (for LH Side)
  1. Lift up the seat track adjusting handle to move the seat to the foremost position.



    B191067
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



63. REMOVE SEAT TRACK OUTER COVER LH (for LH Side)


    B200255
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



64. REMOVE FRONT LH SEAT ASSEMBLY (for LH Side)


    B191041
  1. Remove the 2 bolts.

  1. Lift up the seat track adjusting handle to move the seat to the rearmost position.



    B191042
  1. Remove the 2 bolts.

  1. Lift up the seat track adjusting handle to move the seat to the center position.

  1. Disconnect the seat wire connectors under the seat.

  1. Remove the front seat assembly from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.



65. REMOVE FRONT SEAT HEADREST ASSEMBLY (for RH Side)


66. REMOVE FRONT SEAT TRACK BRACKET COVER INNER RH (for RH Side)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B232171E01
  1. Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



67. REMOVE FRONT SEAT TRACK BRACKET COVER OUTER RH (for RH Side)


    B232172E01
  1. Using a screwdriver, detach the 4 claws in the order shown in the illustration and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



68. REMOVE SEAT TRACK INNER COVER RH (for RH Side)
  1. Operate the power seat switch (slide switch) to move the seat to the foremost position.



    B191067
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



69. REMOVE SEAT TRACK OUTER COVER RH (for RH Side)


    B200255
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



70. REMOVE FRONT RH SEAT ASSEMBLY (for RH Side)
  1. Operate the power seat switch (slide switch) to move the seat to the foremost position.



    B191041
  1. Remove the 2 bolts.

  1. Operate the power seat switch (slide switch) to move the seat to the rearmost position.



    B194824
  1. Remove the 2 bolts.

  1. Operate the power seat switch (slide switch) to move the seat to the center position.



    B167188
  1. Operate the leg support adjustment switch to move the seat cushion to the open position.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the seat wire connectors under the seat.

  1. Remove the front seat assembly from the vehicle.

    NOTICE:
    Be careful not to damage the vehicle body.



71. REMOVE AUDIO AMPLIFIER COVER (for 14 Speakers)


    B190162
  1. Detach the 3 clips and remove the cover.



72. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY (for 14 Speakers)


    B190161
  1. Disconnect the 4 connectors.

  1. Remove the 3 bolts and amplifier.



73. REMOVE REAR NO. 3 AIR DUCT


I104425
  1. Remove the clip.

  1. Detach the 4 claws and remove the air duct.



74. REMOVE REAR NO. 4 AIR DUCT


I104424
  1. Remove the clip.

  1. Detach the 4 claws and remove the air duct.



75. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY


C154523
  1. Remove the bolt and air duct.



76. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY


C154524E01
  1. Put matchmarks on the steering intermediate shaft and the steering column.

  1. Remove the bolt and separate the steering intermediate shaft from the steering column.



77. REMOVE STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)
  1. Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.



    C180952E01
  1. Remove the bolt and 2 nuts. Then remove the steering column from the instrument panel reinforcement.



78. REMOVE STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)


    C159218
  1. Disconnect the connectors and disengage the wire.

  1. Remove the bolt and 2 nuts. Then remove the steering column from the instrument panel reinforcement.



79. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for 14 Speakers)


B228241E01
  1. Slide the slider and disconnect the airbag connector.

  1. Detach the clamp and disconnect the connectors.



  1. Remove the bolt and wire harness.


    B232851

  1. Remove the 2 <F> passenger airbag bolts.



  1. Remove the 3 <C> bolts and 2 <E> nuts.


    B233056E01



  1. Detach the 5 clips and remove the instrument panel.


    B233057



80. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for 8 Speakers)


    B228241E01
  1. Slide the slider and disconnect the airbag connector.

  1. Detach the clamp and disconnect the connectors.



  1. Remove the bolt and wire harness.


    B233058

  1. Remove the 2 <F> passenger airbag bolts.



  1. Remove the 3 <C> bolts and 2 <E> nuts.


    B233056E01



  1. Detach the 5 clips and remove the instrument panel.


    B233057



81. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Move the shift lever to N.



    C155905
  1. Remove the nut and clip, and disconnect the transmission control cable from the automatic transmission.



    C157285
  1. Remove the nut and disconnect the transmission control cable support.



    C179205
  1. Disconnect transmission control cable end from the shift lever.



    C179207
  1. Remove the clip and disconnect the transmission control cable from the shift lever retainer.



    C157286
  1. Remove the 2 bolts and remove the column shift transmission control cable toward the vehicle interior.



82. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY


    C179208
  1. Disconnect the clamp and 2 connectors.

  1. Remove the 4 bolts and transmission floor shift assembly.



83. REMOVE REAR NO. 1 AIR DUCT


I104427
  1. Detach the 3 claws and remove the air duct.



84. REMOVE REAR NO. 2 AIR DUCT


I104426
  1. Detach the 3 claws and remove the air duct.



85. SEPARATE MAIN BODY ECU


E183730
  1. Disconnect the connectors and clamp.

  1. Remove the bolt and nut and separate the main body ECU.



86. REMOVE TURN SIGNAL FLASHER ASSEMBLY


I104429
  1. Disconnect the connector.

  1. Remove the nut and the turn signal flasher.



87. REMOVE NO. 1 ECU INTEGRATION BRACKET


I104430
  1. Disconnect the connectors and clamp.

  1. Remove the bolt and nut and the ECU integration bracket.



88. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Disconnect the connectors and clamps and separate the wire harness.



  1. Remove the bolt and disconnect the ground wire.


    I104431



  1. Remove the instrument panel reinforcement.

    1. for Driver Side:
      Remove the 2 caps and 3 bolts.

    2. for Passenger Side:
      Using a T40 "TORX" socket, remove the 2 "TORX" bolts.

      HINT:
      When removing the bolts, the collars may come off with the bolts.

    3. for Passenger Side:
      Using a 12 mm hexagon wrench, remove the 2 collars.



    4. Remove the 3 bolts, nut and instrument panel reinforcement.


      I104400E01



    I104432
  1. Disconnect the connector and clamp and separate the wire harness.



89. REMOVE FRONT AIR CONDITIONING UNIT


I104401
  1. Remove the 3 bolts, 2 screws and the air conditioning unit.



90. REMOVE ECU COVER


E183926
  1. Remove the 2 screws and ECU cover.