Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short in CAN Bus Lines

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Air conditioning amplifier assembly
  4. 4 wheel drive control ECU (4WD control ECU)*1
  5. Bus buffer ECU*2
  6. Network gateway ECU*3
  7. Center airbag sensor assembly
  8. Steering angle sensor
  9. Main body ECU (cowl side junction block LH)
  10. Power steering ECU assembly
  11. Brake actuator assembly (skid control ECU)
  12. Suspension control ECU*4
  13. Combination meter assembly
  14. No. 1 junction connector
  15. No. 2 junction connector
  16. No. 4 junction connector*3
  1. *1: for 4WD
  2. *2: w/ Bus Buffer ECU
  3. *3: w/ Blind Spot Monitor System
  4. *4: w/ Air Suspension System

WIRING DIAGRAM


C242851E03


C245666E01


C242853E02


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - DLC3)


    C242750E45
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-3 (CANH) - H19-6 (CANH)
    Ignition switch off
    Below 1 Ω
    H115-14 (CANL) - H19- 14 (CANL)
    Ignition switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


4.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    C201374E82
  1. Disconnect the H110 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 20
OK


5.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    C242748E28
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-1 (CANH) - H110-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 10
OK


6.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without an 4WD, go to "Check for Short in CAN Bus Wire (No. 2 Junction Connection - Bus Buffer ECU)".



    C242748E29
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-2 (CANH) - H110-13 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 12
OK


7.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)

NOTICE:
For vehicles without an bus buffer ECU, go to "Check for Short in CAN Bus Wire (No. 2 Junction Connection - Network Gateway ECU)".



    C242748E30
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-5 (CANH) - H110-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 14
OK


8.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NOTICE:
For vehicles without an blind spot monitor system, go to "Check for Short in CAN Bus Wire (No. 2 Junction Connection - ECM)".



    C242748E31
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-6 (CANH) - H110-17 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 16
OK


9.CHECK FOR SHORT IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    C242748E32
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-3 (CANH) - H110-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 18
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

10.CONNECT CONNECTOR
  1. Reconnect the H110 No. 2 junction connector.


NEXT


11.CHECK FOR SHORT IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)


    C227940E03
  1. Disconnect the H24 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H24-11 (CANH) - H24-12 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

12.CONNECT CONNECTOR
  1. Reconnect the H110 No. 2 junction connector.


NEXT


13.CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)


    C242857E01
  1. Disconnect the A28 4 wheel drive control ECU (4WD control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A28-19 (CANH) - A28-20 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to 4 Wheel Drive Control ECU [4WD Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU) (Click here)  

14.CONNECT CONNECTOR
  1. Reconnect the H110 No. 2 junction connector.


NEXT


15.CHECK FOR SHORT IN CAN BUS WIRES (BUS BUFFER ECU)


    C242858E01
  1. Disconnect the H66 bus buffer ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H66-3 (CAN+) - H66-2 (CAN-)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Bus Buffer ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)
OK

REPLACE BUS BUFFER ECU 

16.CONNECT CONNECTOR
  1. Reconnect the H110 No. 2 junction connector.


NEXT


17.CHECK FOR SHORT IN CAN BUS WIRE (NETWORK GATEWAY ECU)


    C242749E03
  1. Disconnect the H120 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H120-16 (CA1H) - H120- 15 (CA1L)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

18.CONNECT CONNECTOR
  1. Reconnect the H110 No. 2 junction connector.


NEXT


19.CHECK SHORT IN CAN BUS WIRE (ECM)


    C234868E05
  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-10 (CANH) - A27-11 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
OK

REPLACE ECM (Click here)  

20.CONNECT CONNECTOR
  1. Reconnect the H110 No. 2 junction connector.


NEXT


21.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C242748E33
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-5 (CANH) - H115-16 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    Result 
    Result
    Proceed to
    OK (w/ Air Suspension System)
    A
    OK (w/o Air Suspension System)
    B
    NG
    C



B
Go to step 32

C
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
A


22.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


23.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR SIDE)


    C201374E82
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 30
OK


24.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - SUSPENSION CONTROL ECU)


    C242859E01
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-6 (CANH) - O42-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
Go to step 26
OK


25.CHECK FOR SHORT IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    C242859E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (CANH) - O41-7 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 4 Junction Connector)



NG
Go to step 28
OK

REPLACE NO. 4 JUNCTION CONNECTOR 

26.CONNECT CONNECTOR
  1. Reconnect the O41 and O42 No. 4 junction connectors.


NEXT


27.CHECK FOR SHORT IN CAN BUS WIRE (SUSPENSION CONTROL ECU)


    C245665E01
  1. Disconnect the O16*1 or O19*2 suspension control ECU connector.

    1. *1: w/ AVS
    2. *2: w/o AVS

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ AVS 
    Tester Connection
    Switch Condition
    Specified Condition
    O16-7 (CANH) - O16-8 (CANL)
    Ignition switch off
    54 to 69 Ω
    w/o AVS 
    Tester Connection
    Switch Condition
    Specified Condition
    O19-29 (CANH) - O19-28 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *A
    w/ AVS
    *B
    w/o AVS
    *a
    Front view of wire harness connector
    (to Suspension Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SUSPENSION CONTROL ECU (CANH, CANL)
OK

REPLACE SUSPENSION CONTROL ECU (Click here)  

28.CONNECT CONNECTOR
  1. Reconnect the O41 and O42 No. 4 junction connectors.


NEXT


29.CHECK FOR SHORT IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    C242857E02
  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

30.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


31.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    C242748E34
  1. Disconnect the H115 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-2 (CANH) - H115-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


32.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    C242748E35
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-1 (CANH) - H115-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 38
OK


33.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C242748E36
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-4 (CANH) - H115-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 40
OK


34.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    C242748E37
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-6 (CANH) - H115-17 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 42
OK


35.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)


    C242748E38
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-7 (CANH) - H115-18 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 44
OK


36.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C242748E39
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-9 (CANH) - H115-20 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    Result 
    Result
    Proceed to
    OK (w/ Air Suspension System)
    A
    OK (w/o Air Suspension System)
    B
    NG
    C



B
Go to step 37

C
Go to step 46
A

REPLACE NO. 1 JUNCTION CONNECTOR 

37.CHECK FOR SHORT IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    C242748E40
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H115-2 (CANH) - H115-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 48
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

38.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


39.CHECK FOR SHORT IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)


    C222818E13
  1. Disconnect the H56 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H56-13 (CANH) - H56-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    Result 
    Result
    Proceed to
    OK (w/ Cool Box)
    A
    OK (w/o Cool Box)
    B
    NG
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

40.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


41.CHECK FOR SHORT IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    C242861E01
  1. Disconnect the H6 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H6-10 (CANH) - H6-9 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

42.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


43.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C242862E01
  1. Disconnect the H2 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-5 (CANH) - H2-6 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) 

44.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


45.CHECK FOR SHORT IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY)


    E211085E07
  1. Disconnect the H112 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H112-1 (CANH) - H112-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

46.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


47.CHECK FOR SHORT IN CAN BUS WIRE (SKID CONTROL ECU)


    C243210E01
  1. Disconnect the A19 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A19-12 (CANH) - A19-13 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

48.CONNECT CONNECTOR
  1. Reconnect the H115 No. 1 junction connector.


NEXT


49.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)


    C242857E02
  1. Disconnect the H37 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)