CAN COMMUNICATION SYSTEM > Open in One Side of CAN Branch Line |
| Symptom | Trouble Area |
| 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen. |
|



| 1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Disconnect the H24 air conditioning amplifier assembly connector.
Select "CAN Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Air Conditioning Amplifier" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "Air Conditioning Amplifier" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H24-11 (CANH) - H24-12 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector (to Air Conditioning Amplifier Assembly) |
|
| ||||
| OK | ||
| ||
| 3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU) |
Disconnect the A28 4 wheel drive control ECU (4WD control ECU) connector.
Select "CAN Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Four Wheel Drive Control" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "Four Wheel Drive Control" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (4WD CONTROL ECU CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A28-19 (CANH) - A28-20 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector (to 4 Wheel Drive Control ECU [4WD Control ECU]) |
|
| ||||
| OK | ||
| ||
| 5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU) |
Disconnect the H66 bus buffer ECU connector.
Select "CAN Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Accessory Gateway" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "Accessory Gateway" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (BUS BUFFER ECU CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H66-3 (CAN+) - H66-2 (CAN-) | Ignition switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector (to Bus Buffer ECU) |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU) |
Disconnect the H120 network gateway ECU connector.
Select "CAN Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "CAN Gateway1" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "CAN Gateway1" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NETWORK GATEWAY ECU CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H120-16 (CA1H) - H120- 15 (CA1L) | Ignition switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector (to Network Gateway ECU) |
|
| ||||
| OK | ||
| ||
| 9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY) |
Disconnect the H56 center airbag sensor assembly connector.
Select "CAN Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Airbag" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "Airbag" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H56-13 (CANH) - H56-22 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector (to Center Airbag Sensor Assembly) |
| Result | Proceed to |
| OK (w/ Cool Box) | A |
| OK (w/o Cool Box) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR) |
Disconnect the H6 steering angle sensor connector.
Select "CAN Bus Check" on the intelligent tester (Click here ).
| Result | Proceed to |
| "Spiral cable (Steering Angle Sensor)" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H6-10 (CANH) - H6-9 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector (to Steering Angle Sensor) |
|
| ||||
| OK | ||
| ||
| 13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU) |
Disconnect the H2 main body ECU (cowl side junction block LH) connector.
Select "CAN Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Main Body" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "Main Body" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H2-5 (CANH) - H2-6 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Main Body ECU [Cowl Side Junction Block LH]) |
|
| ||||
| OK | ||
| ||
| 15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY) |
Disconnect the H112 power steering ECU assembly connector.
Select "CAN Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Power Steering (EPS)" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "Power Steering (EPS)" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H112-1 (CANH) - H112-2 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Power Steering ECU Assembly) |
|
| ||||
| OK | ||
| ||
| 17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU) |
Disconnect the O16*1 or O19*2 suspension control ECU connector.
Select "CAN Bus Check" on the intelligent tester (Click here).
| Result | Proceed to |
| "Suspension Control (Air Suspension)" is not displayed on the intelligent tester | A |
| Several ECUs and sensors in addition to "Suspension Control (Air Suspension)" are displayed on the intelligent tester | B |
|
| ||||
| A | |
| 18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O16-7 (CANH) - O16-8 (CANL) | Ignition switch off | 54 to 69 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| O19-29 (CANH) - O19-28 (CANL) | Ignition switch off | 54 to 69 Ω |
| *A | w/ AVS |
| *B | w/o AVS |
| *a | Front view of wire harness connector (to Suspension Control ECU) |
|
| ||||
| OK | ||
| ||
| 19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE) |
![]() |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Disconnect the A19 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A19-12 (CANH) - A19-13 (CANL) | Ignition switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Brake Actuator Assembly [Skid Control ECU]) |
|
| ||||
| OK | ||
| ||