Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > 4WD Control ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
4WD Control ECU Communication Stop Mode
Either condition is met:
  1. "Four Wheel Drive Control" is not displayed on the "Bus Check" screen.
  2. "4WD Control ECU Communication Stop Mode" in "DTC Communication Table" applies.
  1. Power source or inside of 4 wheel drive control ECU (4WD control ECU)
  2. 4 wheel drive control ECU (4WD control ECU) CAN branch wire or connector
  3. 4 wheel drive control ECU (4WD control ECU)
  1. For vehicles with an 4WD.

WIRING DIAGRAM


C245788E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR OPEN IN CAN BUS WIRE (4WD CONTROL ECU CAN BRANCH WIRE)


    C242857E01
  1. Disconnect the A28 4 wheel drive control ECU (4WD control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A28-19 (CANH) - A28-20 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to 4 Wheel Drive Control ECU [4WD Control ECU])



NG
REPAIR OR REPLACE 4WD CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


4.CHECK HARNESS AND CONNECTOR (4WD CONTROL ECU - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    C245786E01
  1. Disconnect the A29 4 wheel drive control ECU (4WD control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A29-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A29-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to 4 Wheel Drive Control ECU [4WD Control ECU])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE 4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU) (Click here)