Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Open in CAN Main Wire

for Preparation Click here


DESCRIPTION

There may be an open circuit in the CAN main wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
  1. CAN main wire and connector
  2. No. 1 junction connector
  3. No. 2 junction connector
  4. No. 4 junction connector*
  5. ECM
  6. Combination Meter ECU
*: w/ Air Suspension

WIRING DIAGRAM


E158737E03


C211087E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK CONNECTOR
  1. Check the type of No. 2 junction connector.
    Result 
    Result
    Proceed to
    for 2-pin Connector
    A
    for 22-pin Connector
    B



B
Go to step 18
A


3.CHECK DLC3


    H102629E01
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    OK
    70 Ω or higher
    NG

    NOTICE:
    When the measured value is 132 Ω or higher and a CAN communication system DTC is output, there may be a problem besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (Click here) after repairing the trouble area.



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C159609E12
  1. Disconnect the H101 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H101-1 (CANH) - H101-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 6
OK


5.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C137766E80
  1. Disconnect the H91 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H91-1 (CANH) - H91-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Air Suspension)
    B
    NG (w/ Air Suspension)
    C



B
Go to step 11

C
Go to step 13
A

REPLACE NO. 1 JUNCTION CONNECTOR 

6.CONNECT CONNECTOR
  1. Reconnect the H101 No. 1 junction connector.


NEXT


7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    C159609E13
  1. Disconnect the H99 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H99-1 (CANH) - H99-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 9
OK


8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C159609E14
  1. Disconnect the H100 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H100-1 (CANH) - H100-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

9.CONNECT CONNECTOR
  1. Reconnect the H99 No. 2 junction connector.


NEXT


10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 2 JUNCTION CONNECTOR)


    C159493E02
  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-10 (CANH) - A27-11 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE ECM (Click here)  

11.CONNECT CONNECTOR
  1. Reconnect the H91 No. 1 junction connector.


NEXT


12.CHECK OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ECU - NO. 1 JUNCTION CONNECTOR)


    C159487E22
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

13.CONNECT CONNECTOR
  1. Reconnect the H91 No. 1 junction connector.


NEXT


14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)


    E158732E05
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (CANH) - O41-7 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 16
OK


15.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    E158732E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-2 (CANH) - O41-8 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE NO. 4 JUNCTION CONNECTOR 

16.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


17.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ECU - NO. 4 JUNCTION CONNECTOR)


    C159487E22
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

18.CHECK DLC3


    H102629E01
  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    H19-6 (CANH) - H19-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    OK
    70 Ω or higher
    NG

    NOTICE:
    When the measured value is 132 Ω or higher and a CAN communication system DTC is output, there may be a problem besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (Click here) after repairing the trouble area.



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


19.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C159609E12
  1. Disconnect the H101 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H101-1 (CANH) - H101-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 21
OK


20.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C137766E80
  1. Disconnect the H91 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H91-1 (CANH) - H91-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o Air Suspension)
    B
    NG (w/ Air Suspension)
    C



B
Go to step 26

C
Go to step 28
A

REPLACE NO. 1 JUNCTION CONNECTOR 

21.CONNECT CONNECTOR
  1. Reconnect the H101 No. 1 junction connector.


NEXT


22.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    C198236E76
  1. Disconnect the H110 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-3 (CANH) - H110-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 24
OK


23.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C198236E77
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H110-4 (CANH) - H110-15 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

24.CONNECT CONNECTOR
  1. Reconnect the H110 No. 2 junction connector.


NEXT


25.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 2 JUNCTION CONNECTOR)


    C159493E02
  1. Disconnect the A27 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-10 (CANH) - A27-11 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 2 JUNCTION CONNECTOR)
OK

REPLACE ECM (Click here)  

26.CONNECT CONNECTOR
  1. Reconnect the H91 No. 1 junction connector.


NEXT


27.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ECU - NO. 1 JUNCTION CONNECTOR)


    C159487E22
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

28.CONNECT CONNECTOR
  1. Reconnect the H91 No. 1 junction connector.


NEXT


29.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)


    E158732E05
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-1 (CANH) - O41-7 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 31
OK


30.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    E158732E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-2 (CANH) - O41-8 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE NO. 4 JUNCTION CONNECTOR 

31.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


32.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ECU - NO. 4 JUNCTION CONNECTOR)


    C159487E22
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-33 (CANH) - H37-34 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)